10 open source boards using the ESP32-C6-WROOM-1-N4
Real designs built with the ESP32-C6-WROOM-1-N4, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
EuroPlatvorm
nanassound
21.7 × 89.8 mm34 parts4LNo license27ESP32
ESP32-C6-EVB DIMM Rev A
OLIMEX
100 × 70 mm109 parts2LGPL-3.025ESP32
Pajoniiir-M1
dvucinozd
175.6 × 220.1 mm223 parts4LNo license0ESP32
Main routed
0x63616c
54 × 71 mm194 parts4LNo license0ESP32
Preamp Board
colektamu
154.4 × 73.8 mm86 parts2LNo license0ESP32
WashingLineMonitor-P0001
horatioPistachio
58.5 × 43.5 mm58 parts2LNo license0ESP32
ESP32-C6-EVB Rev A
OLIMEX
100 × 70 mm109 parts2LGPL-3.025ESP32
Main test
0x63616c
54 × 71 mm194 parts4LNo license0ESP32
Preamp Board
colektamu
154.4 × 73.8 mm86 parts2LNo license0ESP32
Controller test
0x63616c
61 parts2LNo license0
How designs wire the ESP32-C6-WROOM-1-N4
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ESP32-C6-WROOM-1-N4 connects to, and the resistors, capacitors and other passives placed on it.
- The EN/CHIP_PU_3 pin has a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ.
- The GPIO8_10 pin has a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ.
- The NC_22 pin is left unconnected on 6 of 6 designs.
- The 3V3_2 pin is tied to 3.3V on 5 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GND_1pin 1 | Connected to: GND 83% · a signal 17% | — |
| 3V3_2pin 2 | Connected to: 3.3V 83% · a signal 17% | — |
| EN/CHIP_PU_3pin 3 | Connected to: A connector 50% |
|
| MTDI/GPIO5/ADC1_CH5_5pin 5 | Connected to: A connector 50% · not connected 33% |
|
| GPIO1/ADC1_CH1/XTAL_32K_pin 9 | Connected to: A connector 33% · not connected 17% |
|
| GPIO8_10pin 10 | Connected to: A connector 50% |
|
| GPIO9_15pin 15 | Connected to: A connector 83% |
|
| GPIO18_16pin 16 | Connected to: A connector 50% |
|
| GPIO19_17pin 17 | Connected to: A connector 50% · not connected 17% |
|
| GPIO20_18pin 18 | Connected to: A connector 50% · not connected 17% |
|
| GPIO21_19pin 19 | Connected to: A connector 50% · not connected 17% |
|
| GPIO22_20pin 20 | Connected to: A connector 33% · not connected 17% |
|
| GPIO23_21pin 21 | Connected to: A connector 33% · not connected 17% |
|
| NC_22pin 22 | Connected to: Not connected 100% | — |
| U0TXD/GPIO16_25pin 25 | Connected to: A connector 67% |
|
| GPIO3/ADC1_CH3_26pin 26 | Connected to: A connector 33% · not connected 17% |
|
| GPIO2/ADC1_CH2_27pin 27 | Connected to: A connector 33% · not connected 17% |
|
| GND_28pin 28 | Connected to: GND 83% · a signal 17% | — |
| GND_29pin 29 | Connected to: GND 83% · a signal 17% | — |
| GNDpin 30, 31, 32, 33, 34, 35, 36, 37 | Connected to: GND 67% · a signal 33% | — |
10 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EuroPlatvorm by nanassound, ESP32-C6-EVB DIMM Rev A by OLIMEX, Controller test by 0x63616c and Preamp Board by colektamu.
The ESP32-C6-WROOM-1-N4 in open source designs
The gallery holds 10 open source boards using the ESP32-C6-WROOM-1-N4 from 6 GitHub repositories; a typical one measures about 100 × 71 mm and carries around 98 components.
60% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.
The most starred is EuroPlatvorm by nanassound.
Microcontrollers on boards using the ESP32-C6-WROOM-1-N4
What boards using the ESP32-C6-WROOM-1-N4 are built for
ESP32-C6-WROOM-1-N4: common questions
Where can I find a ESP32-C6-WROOM-1-N4 reference design?
Each of the 10 boards on this page is a real design using the ESP32-C6-WROOM-1-N4. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the ESP32-C6-WROOM-1-N4 EN/CHIP_PU_3 pin?
The EN/CHIP_PU_3 pin has a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the ESP32-C6-WROOM-1-N4.
What pull-up resistor is used on the ESP32-C6-WROOM-1-N4 GPIO8_10 pin?
The GPIO8_10 pin has a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the ESP32-C6-WROOM-1-N4.
How is the ESP32-C6-WROOM-1-N4 NC_22 pin connected?
The NC_22 pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the ESP32-C6-WROOM-1-N4.
Which microcontrollers do boards using the ESP32-C6-WROOM-1-N4 use?
Most are built on ESP32 (10).
How big is a typical board using the ESP32-C6-WROOM-1-N4?
The median is 100 × 71 mm, and 60% are two-layer designs.
What is the most popular open source board using the ESP32-C6-WROOM-1-N4?
By GitHub stars, EuroPlatvorm by nanassound, with 27 stars.
Can I simulate one of these boards using the ESP32-C6-WROOM-1-N4 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.