5 open source boards using the HMHA2801
Real designs built with the HMHA2801, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Peak Power Solar Charger
sPyOpenSource
79 × 77 mm35 parts2LMIT8AVR/Arduino
V4
Arkariusz
30 × 50 mm38 parts2LCC-BY-NC-4.00AVR/Arduino
V4
chipsi
30 × 50 mm38 parts2LCC-BY-NC-4.00AVR/Arduino
V4
orgTestCodacy11KRepos110MB
30 × 50 mm38 parts2LCC-BY-NC-4.00AVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
How designs wire the HMHA2801
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the HMHA2801 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 5 of 5 designs, most often 220 Ω.
- Pin 2 is tied to GND on 5 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| Pin 2 | Connected to: GND 100% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include V4 by stuartpittaway, Peak Power Solar Charger by sPyOpenSource, V4 by Arkariusz and V4 by chipsi.
The HMHA2801 in open source designs
The gallery holds 5 open source boards using the HMHA2801 from 5 GitHub repositories; a typical one measures about 30 × 50 mm and carries around 38 components.
100% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.
The most starred is V4 by stuartpittaway.
Parts used alongside the HMHA2801
Microcontrollers on boards using the HMHA2801
What boards using the HMHA2801 are built for
HMHA2801: common questions
Where can I find a HMHA2801 reference design?
Each of the 5 boards on this page is a real design using the HMHA2801. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the HMHA2801 pin 1?
Pin 1 has a series resistor on 5 of 5 designs, most often 220 Ω. Counted from the KiCad layouts of 5 open source designs using the HMHA2801.
How is the HMHA2801 pin 2 connected?
Pin 2 is tied to GND on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the HMHA2801.
Which microcontrollers do boards using the HMHA2801 use?
Most are built on AVR/Arduino (4).
How big is a typical board using the HMHA2801?
The median is 30 × 50 mm, and 100% are two-layer designs.
What is the most popular open source board using the HMHA2801?
By GitHub stars, V4 by stuartpittaway, with 1,143 stars.
Can I simulate one of these boards using the HMHA2801 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.