15 open source boards using the ATTINY841-SSU
Real designs built with the ATTINY841-SSU, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Darkstar Mk.II
kajusK
34 × 34 mm56 parts2LCERN-OHL-1.27AVR/Arduino
RaspberryPi UPS HAT
gvoigtlaender
65 × 56 mm52 parts2LGPL-3.04AVR/Arduino
Hardware
DC423
58.4 × 118.1 mm34 parts2LNo license3AVR/Arduino
Pi super ups
mairas
65 × 56 mm86 parts2LBSD-3-Clause2ESP32
DIYBMS ESP32 Controller
chipsi
122.5 × 87.6 mm77 parts2LCC-BY-NC-4.00AVR/Arduino
Rpi-GC-Oven-Controller
Pharmaceutical-Analysis
120 × 100 mm58 parts2LNo license0ESP8266
Jotter RevC
SpatialExperienceGroup
76.2 × 76.2 mm46 parts2LMIT0ESP8266
Jotter RevD
SpatialExperienceGroup
76.2 × 76.2 mm46 parts2LMIT0AVR/Arduino
Controller
domenipavec
90 × 30 mm7 parts2LMIT0AVR/Arduino
V4
Arkariusz
30 × 50 mm38 parts2LCC-BY-NC-4.00AVR/Arduino
V4
chipsi
30 × 50 mm38 parts2LCC-BY-NC-4.00AVR/Arduino
Kontroler
domenipavec
147 × 78 mm38 parts2LNo license0AVR/Arduino
V4
orgTestCodacy11KRepos110MB
30 × 50 mm38 parts2LCC-BY-NC-4.00AVR/Arduino
ATtiny841UnoTestShield
SpatialExperienceGroup
68.6 × 53.3 mm20 parts2LMIT0AVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
How designs wire the ATTINY841-SSU
Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the ATTINY841-SSU connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 10 of 12 designs, most often 100 nF (then 1 µF).
- The (PCINT3/SCK/XCK0/T0/TOCC pin has a series resistor on 8 of 12 designs, most often 510 Ω (then 10 kΩ).
- The (PCINT11/DW/RESET/ADC9)P pin has a pull-up to VCC on 6 of 12 designs, most often 10 kΩ.
- The (PCINT4/SCK/SCL/RXD1/T1/ pin has a series resistor on 6 of 12 designs, most often 8.2 kΩ (then 100 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCCpin 1 | Connected to: VCC 83% · a signal 17% |
|
| (PCINT8/CLKI/XTAL1/ADC11pin 2 | Connected to: A connector 25% |
|
| (PCINT11/DW/RESET/ADC9)Ppin 4 | Connected to: A connector 92% |
|
| (PCINT10/RXD0/ICP2/CLKO/pin 5 | Connected to: A connector 33% |
|
| (PCINT7/SS/TXD0/ICP1/TOCpin 6 | Connected to: A connector 25% · not connected 17% |
|
| (PCINT4/SCK/SCL/RXD1/T1/pin 9 | Connected to: A connector 92% |
|
| (PCINT3/SCK/XCK0/T0/TOCCpin 10 | Connected to: Signal 100% |
|
| (PCINT2/SS/RXD0/TOCC1/AIpin 11 | Connected to: A connector 58% |
|
| (PCINT1/MOSI/TXD0/TOCC0/pin 12 | Connected to: A connector 42% |
|
| (PCINT0/MISO/AREF/ADC0)Ppin 13 | Connected to: A connector 33% |
|
| GNDpin 14 | Connected to: GND 100% | — |
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include V4 by stuartpittaway, Darkstar Mk.II by kajusK, RaspberryPi UPS HAT by gvoigtlaender and Hardware by DC423.
The ATTINY841-SSU in open source designs
The gallery holds 15 open source boards using the ATTINY841-SSU from 12 GitHub repositories; a typical one measures about 65 × 56 mm and carries around 38 components.
100% are two-layer designs, the rest use four layers or more, and 47% carry an open source license.
The most starred is V4 by stuartpittaway.
Parts used alongside the ATTINY841-SSU
Microcontrollers on boards using the ATTINY841-SSU
What boards using the ATTINY841-SSU are built for
ATTINY841-SSU: common questions
Where can I find a ATTINY841-SSU reference design?
Each of the 15 boards on this page is a real design using the ATTINY841-SSU. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ATTINY841-SSU VCC pin?
The VCC pin has a decoupling capacitor on 10 of 12 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 12 open source designs using the ATTINY841-SSU.
What resistor goes on the ATTINY841-SSU (PCINT3/SCK/XCK0/T0/TOCC pin?
The (PCINT3/SCK/XCK0/T0/TOCC pin has a series resistor on 8 of 12 designs, most often 510 Ω (then 10 kΩ). Counted from the KiCad layouts of 12 open source designs using the ATTINY841-SSU.
What pull-up resistor is used on the ATTINY841-SSU (PCINT11/DW/RESET/ADC9)P pin?
The (PCINT11/DW/RESET/ADC9)P pin has a pull-up to VCC on 6 of 12 designs, most often 10 kΩ. Counted from the KiCad layouts of 12 open source designs using the ATTINY841-SSU.
Which microcontrollers do boards using the ATTINY841-SSU use?
Most are built on AVR/Arduino (12), ESP8266 (2) and ESP32 (1).
How big is a typical board using the ATTINY841-SSU?
The median is 65 × 56 mm, and 100% are two-layer designs.
What is the most popular open source board using the ATTINY841-SSU?
By GitHub stars, V4 by stuartpittaway, with 1,143 stars.
Can I simulate one of these boards using the ATTINY841-SSU before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.