10 open source boards using the INA181A2
Real designs built with the INA181A2, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Analog i
deimoscontrols
223 × 95 mm568 parts4LNo license43Stigma mission board hysteresis
tudsat-rocket
60 × 130 mm170 parts4LNo license0STM32
RSC-LV3-LVBPS
cyfinfaza
210 × 60 mm118 parts2LNo license0RP2040/RP2350
Supercap
Twisted-Fields
109 × 155.5 mm184 parts4LNo license81Analog frontend panel
deimoscontrols
164.4 × 89.5 mm377 parts4LNo license43STM32
SuperCapPowerBoard G431 Lite V1
evil0knight
60 × 40 mm124 parts4LNo license5Raspberry Pi
Acorn motherboard
Twisted-Fields
106 × 102.3 mm106 parts2LNo license81RP2040/RP2350
Acorn serial
Twisted-Fields
78.7 × 69.4 mm96 parts2LNo license81RP2040/RP2350
Acorn odrive interface
Twisted-Fields
138.5 × 68.2 mm73 parts2LNo license81RP2040/RP2350
Soft start
Twisted-Fields
62 × 65.5 mm55 parts4LNo license81
How designs wire the INA181A2
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the INA181A2 connects to, and the resistors, capacitors and other passives placed on it.
- The + pin has a series resistor on 4 of 5 designs, most often 10 kΩ (then 2 mΩ).
- The - pin has a series resistor on 3 of 5 designs, most often 2 mΩ (then 10 kΩ).
- The V+ pin has a decoupling capacitor on 3 of 4 designs, most often 100 nF (then 4.7 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2 | Connected to: GND 80% · -12V 20% | — |
| +pin 3 | Connected to: Signal 80% · 5V 20% |
|
| -pin 4 | Connected to: Signal 100% |
|
| V+pin 6 | Connected to: 3.3V 75% · a signal 25% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Acorn motherboard by Twisted-Fields, Analog frontend panel by deimoscontrols, SuperCapPowerBoard G431 Lite V1 by evil0knight and RSC-LV3-LVBPS by cyfinfaza.
The INA181A2 in open source designs
The gallery holds 10 open source boards using the INA181A2 from 5 GitHub repositories; a typical one measures about 107.5 × 79.4 mm and carries around 121 components.
60% use four copper layers or more, and 0% carry an open source license.
The most starred is Supercap by Twisted-Fields.
Parts used alongside the INA181A2
Microcontrollers on boards using the INA181A2
What boards using the INA181A2 are built for
INA181A2: common questions
Where can I find a INA181A2 reference design?
Each of the 10 boards on this page is a real design using the INA181A2. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the INA181A2 + pin?
The + pin has a series resistor on 4 of 5 designs, most often 10 kΩ (then 2 mΩ). Counted from the KiCad layouts of 5 open source designs using the INA181A2.
What resistor goes on the INA181A2 - pin?
The - pin has a series resistor on 3 of 5 designs, most often 2 mΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the INA181A2.
What decoupling capacitors do designs use on the INA181A2 V+ pin?
The V+ pin has a decoupling capacitor on 3 of 4 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 5 open source designs using the INA181A2.
Which microcontrollers do boards using the INA181A2 use?
Most are built on RP2040/RP2350 (4), STM32 (3) and Raspberry Pi (1).
How big is a typical board using the INA181A2?
The median is 107.5 × 79.4 mm, and 40% are two-layer designs.
What is the most popular open source board using the INA181A2?
By GitHub stars, Supercap by Twisted-Fields, with 81 stars.
Can I simulate one of these boards using the INA181A2 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.