6 open source boards using the LM1117-ADJ

Real designs built with the LM1117-ADJ, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the LM1117-ADJ

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the LM1117-ADJ connects to, and the resistors, capacitors and other passives placed on it.

  • Pin 1 has a resistor to GND on 4 of 5 designs, most often 300 Ω (then 200 Ω).
  • Pin 1 has a pull-up to 3.3V on 4 of 5 designs, most often 200 Ω (then 121 Ω).
  • Pin 3 has a decoupling capacitor on 4 of 5 designs, most often 47 µF (then 10 µF).
  • Pin 2 is tied to 3.3V on 4 of 5 designs.
Pin 1Connected to: Signal 100%
  • Resistor to GND on 80% · 300 Ω (1), 200 Ω (1)
  • Pull-up to 3.3V on 80% · 200 Ω (1), 121 Ω (1)
  • Capacitor to GND on 40% · 100 nF (1), 4.7 µF (1)
Pin 2Connected to: 3.3V 80% · a signal 20%
Pin 3Connected to: 5V 60% · a signal 40%
  • Decoupling capacitor on 80% · 47 µF (1), 10 µF (1)
Pin 4Connected to: 3.3V 100%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Lab1 by jsjolund, Stebus by laurent-fr, PowerSupply PCB by acalinp and Pcb ctrl esp5v by TobiasKaiser.

The LM1117-ADJ in open source designs

The gallery holds 6 open source boards using the LM1117-ADJ from 5 GitHub repositories; a typical one measures about 86.7 × 79.1 mm and carries around 39 components.

100% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.

The most starred is Lab1 by jsjolund.

Microcontrollers on boards using the LM1117-ADJ

LM1117-ADJ: common questions

Where can I find a LM1117-ADJ reference design?

Each of the 6 boards on this page is a real design using the LM1117-ADJ. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the LM1117-ADJ pin 1?

Pin 1 has a resistor to GND on 4 of 5 designs, most often 300 Ω (then 200 Ω). Counted from the KiCad layouts of 5 open source designs using the LM1117-ADJ.

What decoupling capacitors do designs use on the LM1117-ADJ pin 3?

Pin 3 has a decoupling capacitor on 4 of 5 designs, most often 47 µF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the LM1117-ADJ.

How is the LM1117-ADJ pin 2 connected?

Pin 2 is tied to 3.3V on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the LM1117-ADJ.

Which microcontrollers do boards using the LM1117-ADJ use?

Most are built on ESP32 (1) and STM32 (1).

How big is a typical board using the LM1117-ADJ?

The median is 86.7 × 79.1 mm, and 100% are two-layer designs.

What is the most popular open source board using the LM1117-ADJ?

By GitHub stars, Lab1 by jsjolund, with 26 stars.

Can I simulate one of these boards using the LM1117-ADJ before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part