11 open source boards using the LM2576S-5
Real designs built with the LM2576S-5, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Pimoco
mlnoga
172.2 × 82.8 mm18 parts2LGPL-3.011ESP32
TSAL G V4 2
HKUST-Red-Bird-Racing-EVRT
140 × 60 mm117 parts2LNo license3ESP32
MAZEBLAZE-V3
SurajSonawane2415
111.4 × 88.4 mm22 parts2LNo license2STM32
BLDC motor controller board
Faotik
71.5 × 99 mm93 parts4LNo license1ESP32
VCU V3
HKUST-Red-Bird-Racing-EVRT
114 × 95 mm90 parts2LNo license3Power board
LiU-SeeGoals
166 × 166 mm53 parts4LNo license0ESP32
VCU V2 kicad9
HKUST-Red-Bird-Racing-EVRT
100 × 100 mm79 parts2LNo license3ESP32
SSRU v3.3
HKUST-Red-Bird-Racing-EVRT
95 × 78 mm66 parts2LNo license3ESP32
BSPD
HKUST-Red-Bird-Racing-EVRT
57 × 50 mm60 parts2LNo license3PSU board 1.0
kapibaratomo
50 × 64 mm23 parts2LNo license0ESP32
Front dash unit
HKUST-Red-Bird-Racing-EVRT
101 × 63 mm56 parts2LNo license3
How designs wire the LM2576S-5
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LM2576S-5 connects to, and the resistors, capacitors and other passives placed on it.
- The OUT pin has a inductor on 5 of 6 designs, most often 100 µH (then 100 H).
- The FB pin is tied to 5V on 5 of 6 designs.
- The ON/OFF pin is tied to GND on 5 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VINpin 1 | Connected to: VCC 50% · a signal 50% |
|
| OUTpin 2 | Connected to: Signal 100% |
|
| GNDpin 3 | Connected to: GND 100% | — |
| FBpin 4 | Connected to: 5V 83% · a signal 17% | — |
| ON/OFFpin 5 | Connected to: GND 83% · 5V 17% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Pimoco by mlnoga, BSPD by HKUST-Red-Bird-Racing-EVRT, MAZEBLAZE-V3 by SurajSonawane2415 and BLDC motor controller board by Faotik.
The LM2576S-5 in open source designs
The gallery holds 11 open source boards using the LM2576S-5 from 6 GitHub repositories; a typical one measures about 101 × 82.8 mm and carries around 60 components.
82% are two-layer designs, the rest use four layers or more, and 9% carry an open source license.
The most starred is Pimoco by mlnoga.
Parts used alongside the LM2576S-5
What boards using the LM2576S-5 are built for
LM2576S-5: common questions
Where can I find a LM2576S-5 reference design?
Each of the 11 boards on this page is a real design using the LM2576S-5. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM2576S-5 OUT pin connected?
The OUT pin has a inductor on 5 of 6 designs, most often 100 µH (then 100 H). Counted from the KiCad layouts of 6 open source designs using the LM2576S-5.
How is the LM2576S-5 FB pin connected?
The FB pin is tied to 5V on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the LM2576S-5.
How is the LM2576S-5 ON/OFF pin connected?
The ON/OFF pin is tied to GND on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the LM2576S-5.
Which microcontrollers do boards using the LM2576S-5 use?
Most are built on ESP32 (7) and STM32 (1).
How big is a typical board using the LM2576S-5?
The median is 101 × 82.8 mm, and 82% are two-layer designs.
What is the most popular open source board using the LM2576S-5?
By GitHub stars, Pimoco by mlnoga, with 11 stars.
Can I simulate one of these boards using the LM2576S-5 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.