7 open source boards using the LM5145RGYR

Real designs built with the LM5145RGYR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the LM5145RGYR

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LM5145RGYR connects to, and the resistors, capacitors and other passives placed on it.

  • The EN_UVLO_1 pin has a resistor to GND on 6 of 6 designs, most often 16.5 kΩ (then 10 kΩ).
  • The RT_2 pin has a resistor to GND on 5 of 6 designs, most often 47 kΩ (then 28.7 kΩ).
  • The SS_TRK_3 pin has a capacitor to GND on 5 of 6 designs, most often 10 nF (then 47 nF).
  • The COMP_4 pin has a series capacitor on 5 of 6 designs, most often 8.2 nF (then 150 pF).
EN_UVLO_1pin 1Connected to: Signal 100%
  • Resistor to GND on 100% · 16.5 kΩ (1), 10 kΩ (1), 13 kΩ (1)
  • Pull-up to VBUS_F on 67% · 100 kΩ (1), 82 kΩ (1), 200 kΩ (1)
RT_2pin 2Connected to: Signal 100%
  • Resistor to GND on 83% · 47 kΩ (1), 28.7 kΩ (1), 24.9 kΩ (1)
SS_TRK_3pin 3Connected to: Signal 100%
  • Capacitor to GND on 83% · 10 nF (1), 47 nF (1), 33 nF (1)
COMP_4pin 4Connected to: Signal 100%
  • Series capacitor on 83% · 8.2 nF (2), 150 pF (1), 10 nF (1)
FB_5pin 5Connected to: Signal 100%
  • Series capacitor on 83% · 470 pF (2), 3.3 nF (2), 150 pF (1)
  • Resistor to GND on 83% · 3.9 kΩ (1), 1 kΩ (1), 2.37 kΩ (1)
  • Series resistor on 67% · 3.9 kΩ (2), 10 kΩ (1), 25.5 kΩ (1)
  • Pull-up to 12V on 33% · 33.2 kΩ (1), 137 kΩ (1)
AGND_6pin 6Connected to: GND 100%
SYNCOUT_7pin 7Connected to: Not connected 100%
NC_9pin 9Connected to: Not connected 83% · GND 17%
PGOOD_10pin 10Connected to: Signal 67% · not connected 33%
  • Pull-up to 5V on 50% · 20 kΩ (2), 100 kΩ (1)
  • Series resistor on 33% · 20 kΩ (2)
ILIM_11pin 11Connected to: Signal 100%
  • Series resistor on 83% · 365 Ω (2), 470 Ω (1), 240 Ω (1)
  • Capacitor to GND on 50% · 15 pF (1), 10 pF (1), 5.1 pF (1)
PGND_12pin 12Connected to: GND 83% · a signal 17%
VCC_14pin 14Connected to: VCC 50% · a signal 50%
  • Decoupling capacitor on 50% · 2.2 µF (3)
EP_15pin 15Connected to: GND 67% · not connected 17% · a signal 17%
NC_16pin 16Connected to: Not connected 83% · GND 17%
BST_17pin 17Connected to: Signal 100%
  • Series capacitor on 67% · 100 nF (4)
SW_19pin 19Connected to: Signal 100%
  • Series capacitor on 83% · 100 nF (5), 1 nF (1)
  • Inductor on 83% · 4.7 µH (1), 10 µH (1), 3.3 µH (1)
  • Series resistor on 83% · 365 Ω (2), 470 Ω (1), 2.2 Ω (1)
VIN_20pin 20Connected to: Signal 67% · 19V 33%
  • Series resistor on 33% · 10 kΩ (2), 100 kΩ (1)
  • Series capacitor on 33% · 470 nF (2), 4.7 µF (2), 47 nF (1)
  • Capacitor to GND on 33% · 100 nF (2)
  • Pull-up to VBUS_F on 33% · 4.7 Ω (1), 2.1 Ω (1)
EP_21pin 21Connected to: GND 83% · a signal 17%

3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Power board v1 by misko, EEZ DIB DCP405plus by eez-open, Phase1-module by udaravima and Robothardware by des256.

The LM5145RGYR in open source designs

The gallery holds 7 open source boards using the LM5145RGYR from 6 GitHub repositories; a typical one measures about 120 × 80 mm and carries around 136 components.

71% use four copper layers or more, and 29% carry an open source license.

The most starred is Power board v1 by misko.

Microcontrollers on boards using the LM5145RGYR

What boards using the LM5145RGYR are built for

LM5145RGYR: common questions

Where can I find a LM5145RGYR reference design?

Each of the 7 boards on this page is a real design using the LM5145RGYR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the LM5145RGYR EN_UVLO_1 pin?

The EN_UVLO_1 pin has a resistor to GND on 6 of 6 designs, most often 16.5 kΩ (then 10 kΩ). Counted from the KiCad layouts of 6 open source designs using the LM5145RGYR.

What resistor goes on the LM5145RGYR RT_2 pin?

The RT_2 pin has a resistor to GND on 5 of 6 designs, most often 47 kΩ (then 28.7 kΩ). Counted from the KiCad layouts of 6 open source designs using the LM5145RGYR.

How is the LM5145RGYR SS_TRK_3 pin connected?

The SS_TRK_3 pin has a capacitor to GND on 5 of 6 designs, most often 10 nF (then 47 nF). Counted from the KiCad layouts of 6 open source designs using the LM5145RGYR.

Which microcontrollers do boards using the LM5145RGYR use?

Most are built on STM32 (3) and AVR/Arduino (2).

How big is a typical board using the LM5145RGYR?

The median is 120 × 80 mm, and 29% are two-layer designs.

What is the most popular open source board using the LM5145RGYR?

By GitHub stars, Power board v1 by misko, with 12 stars.

Can I simulate one of these boards using the LM5145RGYR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part