6 open source boards using the LMR33640ADDAR
Real designs built with the LMR33640ADDAR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
PXU
Andr-Zero
198 × 64.5 mm119 parts4LCERN-OHL-S-2.0104ESP32
HolyGrail
whbCool
157 × 73 mm195 parts6LNo license1RP2040/RP2350
Multiroom amp
rocketreading44
327 × 112 mm312 parts4LNo license0KTHFS DCDC ${DOC TYPE}
erikAWTO
95 × 95 mm180 parts4LNo license0Raspberry Pi
Fable sbc test
geilevideossos-gamedev
100 × 74 mm138 parts4LGPL-3.00RP2040/RP2350
LEC Main Board
MSTRocketDesignTeam
146.1 × 144.9 mm51 parts2LAGPL-3.02
How designs wire the LMR33640ADDAR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LMR33640ADDAR connects to, and the resistors, capacitors and other passives placed on it.
- The FB pin has a resistor to GND on 6 of 6 designs, most often 24.9 kΩ (then 9.53 kΩ).
- The VCC pin has a capacitor to GND on 6 of 6 designs, most often 1 µF.
- The BOOT pin has a series capacitor on 6 of 6 designs, most often 100 nF.
- The SW pin has a inductor on 6 of 6 designs, most often 6.8 µH (then 7.45 GH).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 9 | Connected to: GND 100% | — |
| VINpin 2 | Connected to: 20V 83% · a signal 17% |
|
| ENpin 3 | Connected to: Signal 83% · 24V 17% |
|
| PGpin 4 | Connected to: Not connected 67% · a signal 33% |
|
| FBpin 5 | Connected to: Signal 100% |
|
| VCCpin 6 | Connected to: Signal 100% |
|
| BOOTpin 7 | Connected to: Signal 100% |
|
| SWpin 8 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PXU by Andr-Zero, LEC Main Board by MSTRocketDesignTeam, HolyGrail by whbCool and KTHFS DCDC ${DOC TYPE} by erikAWTO.
The LMR33640ADDAR in open source designs
The gallery holds 6 open source boards using the LMR33640ADDAR from 6 GitHub repositories; a typical one measures about 151.5 × 84.5 mm and carries around 159 components.
83% use four copper layers or more, and 50% carry an open source license.
The most starred is PXU by Andr-Zero.
Parts used alongside the LMR33640ADDAR
Microcontrollers on boards using the LMR33640ADDAR
What boards using the LMR33640ADDAR are built for
LMR33640ADDAR: common questions
Where can I find a LMR33640ADDAR reference design?
Each of the 6 boards on this page is a real design using the LMR33640ADDAR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LMR33640ADDAR FB pin?
The FB pin has a resistor to GND on 6 of 6 designs, most often 24.9 kΩ (then 9.53 kΩ). Counted from the KiCad layouts of 6 open source designs using the LMR33640ADDAR.
How is the LMR33640ADDAR VCC pin connected?
The VCC pin has a capacitor to GND on 6 of 6 designs, most often 1 µF. Counted from the KiCad layouts of 6 open source designs using the LMR33640ADDAR.
How is the LMR33640ADDAR BOOT pin connected?
The BOOT pin has a series capacitor on 6 of 6 designs, most often 100 nF. Counted from the KiCad layouts of 6 open source designs using the LMR33640ADDAR.
Which microcontrollers do boards using the LMR33640ADDAR use?
Most are built on RP2040/RP2350 (2), ESP32 (1) and Raspberry Pi (1).
How big is a typical board using the LMR33640ADDAR?
The median is 151.5 × 84.5 mm, and 17% are two-layer designs.
What is the most popular open source board using the LMR33640ADDAR?
By GitHub stars, PXU by Andr-Zero, with 104 stars.
Can I simulate one of these boards using the LMR33640ADDAR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.