8 open source boards using the LT6106
Real designs built with the LT6106, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
6xUSB PowMet
aleksejm
92.3 × 69 mm161 parts2LNo license7AVR/Arduino
GroED
BB-KING777
98.1 × 98.1 mm257 parts2LNo license0ESP8266
PowMetV2.2
aleksejm
95.2 × 67.5 mm155 parts2LNo license7Power Board
Open-Vent-Bristol
174 × 57.5 mm79 parts2LMIT2Wireless proj
lzyang2000
77.9 × 54.6 mm19 parts2LNo license1AVR/Arduino
6xUSB PowMet hub
aleksejm
201.4 × 150.7 mm97 parts2LNo license7STM32
LargeMD
Tomoshibi-technology
110 × 60 mm148 parts2LMIT1STM32
SmallMD
Tomoshibi-technology
90 × 40 mm142 parts2LMIT1
How designs wire the LT6106
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the LT6106 connects to, and the resistors, capacitors and other passives placed on it.
- The V- pin is tied to GND on 5 of 5 designs.
- Pin 1 has a resistor to GND on 4 of 5 designs, most often 1 kΩ (then 4.99 kΩ).
- The + pin has a series resistor on 3 of 5 designs, most often 200 Ω (then 40 mΩ).
- The V+ pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF (then 470 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: The microcontroller 60%, a connector 40% |
|
| V-pin 2 | Connected to: GND 100% | — |
| -pin 3 | Connected to: Signal 100% |
|
| +pin 4 | Connected to: Signal 100% |
|
| V+pin 5 | Connected to: 5V 80% · a signal 20% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include 6xUSB PowMet by aleksejm, Power Board by Open-Vent-Bristol, Wireless proj by lzyang2000 and LargeMD by Tomoshibi-technology.
The LT6106 in open source designs
The gallery holds 8 open source boards using the LT6106 from 5 GitHub repositories; a typical one measures about 96.6 × 63.8 mm and carries around 145 components.
100% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is 6xUSB PowMet by aleksejm.
Microcontrollers on boards using the LT6106
What boards using the LT6106 are built for
LT6106: common questions
Where can I find a LT6106 reference design?
Each of the 8 boards on this page is a real design using the LT6106. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LT6106 V- pin connected?
The V- pin is tied to GND on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the LT6106.
What resistor goes on the LT6106 pin 1?
Pin 1 has a resistor to GND on 4 of 5 designs, most often 1 kΩ (then 4.99 kΩ). Counted from the KiCad layouts of 5 open source designs using the LT6106.
What resistor goes on the LT6106 + pin?
The + pin has a series resistor on 3 of 5 designs, most often 200 Ω (then 40 mΩ). Counted from the KiCad layouts of 5 open source designs using the LT6106.
Which microcontrollers do boards using the LT6106 use?
Most are built on AVR/Arduino (2), ESP8266 (2) and STM32 (2).
How big is a typical board using the LT6106?
The median is 96.6 × 63.8 mm, and 100% are two-layer designs.
What is the most popular open source board using the LT6106?
By GitHub stars, 6xUSB PowMet by aleksejm, with 7 stars.
Can I simulate one of these boards using the LT6106 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.