6 open source boards using the MAX98357AETE
Real designs built with the MAX98357AETE, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
NXP
Mega-Cube-Board
MaltWhiskey
200 × 54 mm100 parts4LNo license763ESP32
ESPHome-Indoor-Multi-Sensor
mikelawrence
52.5 × 59.7 mm97 parts4LCERN-OHL-P-2.012ESP32
Nebula
Thecactusman0
39.7 × 39.9 mm59 parts2LNo license4AVR/Arduino
Backplane
PurkkaKoodari
200 × 100 mm96 parts2LMIT2ESP32
Stencil
mikelawrence
52.5 × 59.7 mm97 parts4LCERN-OHL-P-2.012RP2040/RP2350
Audio player
Vaaarad07
74 × 63.1 mm84 parts2LMIT10
How designs wire the MAX98357AETE
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MAX98357AETE connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pins have a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 10 µF).
- The SD_MODE pin has a series resistor on 3 of 5 designs, most often 210 kΩ (then 634 kΩ).
- The OUTP pin has a ferrite bead on 2 of 5 designs.
- The OUTN pin has a ferrite bead on 2 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 3, 11, 15 | Connected to: GND 100% | — |
| SD_MODEpin 4 | Connected to: Signal 80% · VCC 20% |
|
| NCpin 5, 6, 12, 13 | Connected to: Not connected 100% | — |
| VDDpin 7, 8 | Connected to: 3.3V 100% |
|
| OUTPpin 9 | Connected to: A connector 40% |
|
| OUTNpin 10 | Connected to: A connector 40% |
|
| EPpin 17 | Connected to: GND 80% · not connected 20% | — |
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Mega-Cube-Board by MaltWhiskey, ESPHome-Indoor-Multi-Sensor by mikelawrence, Audio player by Vaaarad07 and Nebula by Thecactusman0.
The MAX98357AETE in open source designs
The gallery holds 6 open source boards using the MAX98357AETE from 5 GitHub repositories; a typical one measures about 63.3 × 59.7 mm and carries around 97 components.
50% are two-layer designs, the rest use four layers or more, and 67% carry an open source license.
The most starred is Mega-Cube-Board by MaltWhiskey.
Microcontrollers on boards using the MAX98357AETE
What boards using the MAX98357AETE are built for
MAX98357AETE: common questions
Where can I find a MAX98357AETE reference design?
Each of the 6 boards on this page is a real design using the MAX98357AETE. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MAX98357AETE VDD pin?
The VDD pins have a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the MAX98357AETE.
What resistor goes on the MAX98357AETE SD_MODE pin?
The SD_MODE pin has a series resistor on 3 of 5 designs, most often 210 kΩ (then 634 kΩ). Counted from the KiCad layouts of 5 open source designs using the MAX98357AETE.
How is the MAX98357AETE OUTP pin connected?
The OUTP pin has a ferrite bead on 2 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the MAX98357AETE.
Which microcontrollers do boards using the MAX98357AETE use?
Most are built on ESP32 (3), AVR/Arduino (1), NXP (1) and RP2040/RP2350 (1).
How big is a typical board using the MAX98357AETE?
The median is 63.3 × 59.7 mm, and 50% are two-layer designs.
What is the most popular open source board using the MAX98357AETE?
By GitHub stars, Mega-Cube-Board by MaltWhiskey, with 763 stars.
Can I simulate one of these boards using the MAX98357AETE before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.