14 open source boards using the Opamp_Dual_Generic
Real designs built with the Opamp_Dual_Generic, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Lofence
kiu
78 × 130 mm57 parts2LMIT141Mu lna
marcoreps
100 × 77.8 mm55 parts2LNo license36AVR/Arduino
Vm101-inout
mirdej
130 × 105 mm233 parts4LNo license23Motor driver
ETAChalmers
110 × 160 mm156 parts2LNo license0Car bluetooth
ChipCE
99.8 × 48.3 mm53 parts2LGPL-3.02Back power board
limblab
44.2 × 45.5 mm14 parts2LNo license2PhotoDiode MDversion1.2
LeonAbelmann
27.2 × 27.2 mm17 parts4LMIT1PhotoDiode MDversion1.2
CameronBrooks11
27.2 × 27.2 mm17 parts4LMIT0PhotoDiode MDversion1.3
LeonAbelmann
27.2 × 27.2 mm16 parts4LMIT1PhotoDiode MDversion1.3
CameronBrooks11
27.2 × 27.2 mm16 parts4LMIT0Sensorboard tester
jkominek
83.8 × 83.8 mm33 parts2LCustom license53PhotoDiode MDversion
LeonAbelmann
26.8 × 26.8 mm13 parts4LMIT1PhotoDiode MDversion
CameronBrooks11
26.8 × 26.8 mm13 parts4LMIT0Vm130-audio out
mirdej
47.9 × 46.4 mm52 parts2LNo license23
How designs wire the Opamp_Dual_Generic
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the Opamp_Dual_Generic connects to, and the resistors, capacitors and other passives placed on it.
- The - pins have a series resistor on 8 of 9 designs, most often 3.3 kΩ (then 15 kΩ).
- Pin 1 has a series resistor on 7 of 9 designs, most often 3.3 kΩ (then 15 kΩ).
- The V+ pin has a decoupling capacitor on 7 of 9 designs, most often 100 nF (then 10 nF).
- The + pins have a series resistor on 6 of 9 designs, most often 1 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 89% |
|
| -pin 2, 6 | Connected to: Signal 94% |
|
| +pin 3, 5 | Connected to: Signal 78% · GND 22% |
|
| V-pin 4 | Connected to: GND 78% · -12V 22% | — |
| Pin 7 | Connected to: A connector 33% |
|
| V+pin 8 | Connected to: 12V 67% · a signal 33% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Lofence by kiu, Sensorboard tester by jkominek, Mu lna by marcoreps and Vm101-inout by mirdej.
The Opamp_Dual_Generic in open source designs
The gallery holds 14 open source boards using the Opamp_Dual_Generic from 9 GitHub repositories; a typical one measures about 46.1 × 45.9 mm and carries around 25 components.
50% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.
The most starred is Lofence by kiu.
Parts used alongside the Opamp_Dual_Generic
Microcontrollers on boards using the Opamp_Dual_Generic
What boards using the Opamp_Dual_Generic are built for
Opamp_Dual_Generic: common questions
Where can I find a Opamp_Dual_Generic reference design?
Each of the 14 boards on this page is a real design using the Opamp_Dual_Generic. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the Opamp_Dual_Generic - pin?
The - pins have a series resistor on 8 of 9 designs, most often 3.3 kΩ (then 15 kΩ). Counted from the KiCad layouts of 9 open source designs using the Opamp_Dual_Generic.
What resistor goes on the Opamp_Dual_Generic pin 1?
Pin 1 has a series resistor on 7 of 9 designs, most often 3.3 kΩ (then 15 kΩ). Counted from the KiCad layouts of 9 open source designs using the Opamp_Dual_Generic.
What decoupling capacitors do designs use on the Opamp_Dual_Generic V+ pin?
The V+ pin has a decoupling capacitor on 7 of 9 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 9 open source designs using the Opamp_Dual_Generic.
Which microcontrollers do boards using the Opamp_Dual_Generic use?
Most are built on AVR/Arduino (2).
How big is a typical board using the Opamp_Dual_Generic?
The median is 46.1 × 45.9 mm, and 50% are two-layer designs.
What is the most popular open source board using the Opamp_Dual_Generic?
By GitHub stars, Lofence by kiu, with 141 stars.
Can I simulate one of these boards using the Opamp_Dual_Generic before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.