6 open source boards using the SN74LVC2G08DCTR

Real designs built with the SN74LVC2G08DCTR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the SN74LVC2G08DCTR

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the SN74LVC2G08DCTR connects to, and the resistors, capacitors and other passives placed on it.

  • The I0_1 pin has a resistor to GND on 4 of 5 designs, most often 10 kΩ (then 100 kΩ).
  • The I0_5 pin has a resistor to GND on 4 of 5 designs, most often 10 kΩ (then 100 kΩ).
  • The O_7 pin has a series resistor on 4 of 5 designs, most often 33 Ω (then 560 Ω).
  • The VDD_8 pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF.
I0_1pin 1Connected to: The microcontroller 40%
  • Resistor to GND on 80% · 10 kΩ (3), 100 kΩ (1)
I1_2pin 2Connected to: Signal 100%
  • Pull-up to 3.3V on 60% · 10 kΩ (2), 4.7 kΩ (1)
  • Resistor to GND on 40% · 100 kΩ (2)
O_3pin 3Connected to: Signal 100%
  • Series resistor on 60% · 33 Ω (2), 4.7 kΩ (1)
VSS_4pin 4Connected to: GND 100%
I0_5pin 5Connected to: The microcontroller 40%
  • Resistor to GND on 80% · 10 kΩ (3), 100 kΩ (1)
I1_6pin 6Connected to: Signal 100%
  • Pull-up to 3.3V on 40% · 10 kΩ (2)
  • Resistor to GND on 40% · 100 kΩ (2)
O_7pin 7Connected to: Signal 100%
  • Series resistor on 80% · 33 Ω (2), 560 Ω (1), 4.7 kΩ (1)
VDD_8pin 8Connected to: 3.3V 100%
  • Decoupling capacitor on 80% · 100 nF (5)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EEZ DIB DCP405plus by eez-open, Esp32Tap - ESP32-S3 Precor serial bus tap by scottmsilver, AIPE 48V to 24V / 1kW by FulongLi and Controller core reva by itorralbo.

The SN74LVC2G08DCTR in open source designs

The gallery holds 6 open source boards using the SN74LVC2G08DCTR from 5 GitHub repositories; a typical one measures about 130.8 × 96.8 mm and carries around 193 components.

100% use four copper layers or more, and 33% carry an open source license.

The most starred is EEZ DIB DCP405plus by eez-open.

Parts used alongside the SN74LVC2G08DCTR

Microcontrollers on boards using the SN74LVC2G08DCTR

What boards using the SN74LVC2G08DCTR are built for

SN74LVC2G08DCTR: common questions

Where can I find a SN74LVC2G08DCTR reference design?

Each of the 6 boards on this page is a real design using the SN74LVC2G08DCTR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the SN74LVC2G08DCTR I0_1 pin?

The I0_1 pin has a resistor to GND on 4 of 5 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 5 open source designs using the SN74LVC2G08DCTR.

What resistor goes on the SN74LVC2G08DCTR I0_5 pin?

The I0_5 pin has a resistor to GND on 4 of 5 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 5 open source designs using the SN74LVC2G08DCTR.

What resistor goes on the SN74LVC2G08DCTR O_7 pin?

The O_7 pin has a series resistor on 4 of 5 designs, most often 33 Ω (then 560 Ω). Counted from the KiCad layouts of 5 open source designs using the SN74LVC2G08DCTR.

Which microcontrollers do boards using the SN74LVC2G08DCTR use?

Most are built on ESP32 (2) and STM32 (1).

How big is a typical board using the SN74LVC2G08DCTR?

The median is 130.8 × 96.8 mm, and 0% are two-layer designs.

What is the most popular open source board using the SN74LVC2G08DCTR?

By GitHub stars, EEZ DIB DCP405plus by eez-open, with 11 stars.

Can I simulate one of these boards using the SN74LVC2G08DCTR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part