10 open source boards using the SPI Flash
Real designs built with the SPI Flash, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Anyon e motherboard
byrantech
133 × 92 mm258 parts6LMIT4.3kRP2040/RP2350
Usb sniffer lite
ataradov
43.4 × 18.8 mm38 parts2LBSD-3-Clause701STM32
OzzyBoard
vbalsan
100 × 100 mm278 parts4LGPL-2.04- schematic only · 57 partsMicrochip SAM
Radio Software
silver-sat
57 partsNo license0 Microchip SAM
Adafruit Circuit Playground Express
hulkco
50.8 × 50.6 mm78 partsNo license15FPGA
Tomu, I'm
theacodes
13 × 9.4 mm40 parts4LMIT1.1kFPGA
Tomu, I'm
clintonimaroo
13 × 9.4 mm40 parts4LNo license0FPGA
Tomu, I'm
grokicad
13 × 9.4 mm40 parts4LNo license26Single stencil
linuxboot
40.2 × 92.5 mm20 parts2LGPL-3.04Adapter soldered
linuxboot
11.5 × 17.9 mm12 parts2LGPL-3.04
How designs wire the SPI Flash
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the SPI Flash connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 6 of 8 designs, most often 100 nF (then 1 µF).
- The CS pin has a pull-up to 3.3V on 4 of 8 designs, most often 201 Ω (then 10 kΩ).
- Pin 9 is left unconnected on 4 of 4 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CSpin 1 | Connected to: The microcontroller 63% |
|
| GNDpin 4 | Connected to: GND 100% | — |
| VCCpin 8 | Connected to: 3.3V 100% |
|
| Pin 9 | Connected to: Not connected 100% | — |
5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Anyon e motherboard by byrantech, Tomu, I'm by theacodes, Usb sniffer lite by ataradov and Tomu, I'm by grokicad.
The SPI Flash in open source designs
The gallery holds 10 open source boards using the SPI Flash from 9 GitHub repositories; a typical one measures about 40.2 × 18.8 mm and carries around 40 components.
63% use four copper layers or more, and 60% carry an open source license.
The most starred is Anyon e motherboard by byrantech.
Parts used alongside the SPI Flash
Microcontrollers on boards using the SPI Flash
What boards using the SPI Flash are built for
SPI Flash: common questions
Where can I find a SPI Flash reference design?
Each of the 10 boards on this page is a real design using the SPI Flash. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the SPI Flash VCC pin?
The VCC pin has a decoupling capacitor on 6 of 8 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 8 open source designs using the SPI Flash.
What pull-up resistor is used on the SPI Flash CS pin?
The CS pin has a pull-up to 3.3V on 4 of 8 designs, most often 201 Ω (then 10 kΩ). Counted from the KiCad layouts of 8 open source designs using the SPI Flash.
How is the SPI Flash pin 9 connected?
Pin 9 is left unconnected on 4 of 4 designs. Counted from the KiCad layouts of 8 open source designs using the SPI Flash.
What parts are used alongside the SPI Flash?
The Crystal Oscillator, ICE40UP5K-UWG30, LDO-X2SON-1.2V, LDO-X2SON-2.5V and LDO-X2SON-3.3V appear in the most repositories here.
Which microcontrollers do boards using the SPI Flash use?
Most are built on FPGA (3), Microchip SAM (2), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the SPI Flash?
The median is 40.2 × 18.8 mm, and 38% are two-layer designs.
What is the most popular open source board using the SPI Flash?
By GitHub stars, Anyon e motherboard by byrantech, with 4,264 stars.
Can I simulate one of these boards using the SPI Flash before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.