6 open source boards using the SX1276

Real designs built with the SX1276, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the SX1276

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the SX1276 connects to, and the resistors, capacitors and other passives placed on it.

  • The GND_2 pin has a capacitor to GND on 4 of 5 designs, most often 100 nF.
  • The TXD_4 pin has a capacitor to GND on 4 of 5 designs, most often 100 nF.
  • The VBAT_DIG_14 pin has a decoupling capacitor on 4 of 4 designs, most often 100 nF.
  • The VBAT_RF_24 pin has a decoupling capacitor on 4 of 4 designs, most often 100 nF (then 47 pF).
GND_2pin 2Connected to: Signal 80% · GND 20%
  • Capacitor to GND on 80% · 100 nF (4)
RXD_3pin 3Connected to: 3.3V 80% · a signal 20%
TXD_4pin 4Connected to: Signal 100%
  • Capacitor to GND on 80% · 100 nF (4)
AUX_5pin 5Connected to: Signal 100%
  • Capacitor to GND on 60% · 15 pF (2), 10 pF (1)
  • Crystal on 40% · 32 MHz (2)
M0_6pin 6Connected to: Signal 80% · not connected 20%
  • Capacitor to GND on 60% · 15 pF (2), 10 pF (1)
  • Crystal on 40% · 32 MHz (2)
M1_7pin 7Connected to: A connector 40%, the microcontroller 40%
  • Pull-up to 1.8V on 40% · 10 kΩ (2)
DIO4_12pin 12Connected to: Not connected 75% · a signal 25%
VBAT_DIG_14pin 14Connected to: 3.3V 100%
  • Decoupling capacitor on 100% · 100 nF (4)
GND_15pin 15Connected to: GND 100%
RXTX/RF_MOD_20pin 20Connected to: Signal 75% · not connected 25%
  • Series resistor on 50% · 1 kΩ (1), 0 Ω (1)
RFI_HF_21pin 21Connected to: Signal 75% · not connected 25%
  • Inductor on 50% · 10 nH (2)
GND_23pin 23Connected to: GND 100%
VBAT_RF_24pin 24Connected to: 3.3V 100%
  • Decoupling capacitor on 100% · 100 nF (5), 47 pF (2), 10 µF (2)
VR_PA_25pin 25Connected to: Signal 100%
  • Capacitor to GND on 100% · 10 nF (3), 47 pF (2), 100 pF (1)
  • Inductor on 75% · 33 nH (2), 47 nH (1)
GND_26pin 26Connected to: GND 100%
PA_BOOST_27pin 27Connected to: Not connected 75% · a signal 25%
RFO_LF_28pin 28Connected to: Not connected 50% · a signal 50%
  • Series resistor on 50% · 0 Ω (1)
GND_29pin 29Connected to: GND 100%

11 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include TinyTracker by daveshah1, Lora modul by balcer, LoRaPP by daveshah1 and Micro by IslamHUFE.

The SX1276 in open source designs

The gallery holds 6 open source boards using the SX1276 from 6 GitHub repositories; a typical one measures about 50 × 24.5 mm and carries around 51 components.

100% use four copper layers or more, and 33% carry an open source license.

The most starred is TinyTracker by daveshah1.

Parts used alongside the SX1276

Microcontrollers on boards using the SX1276

What boards using the SX1276 are built for

SX1276: common questions

Where can I find a SX1276 reference design?

Each of the 6 boards on this page is a real design using the SX1276. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the SX1276 GND_2 pin connected?

The GND_2 pin has a capacitor to GND on 4 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the SX1276.

How is the SX1276 TXD_4 pin connected?

The TXD_4 pin has a capacitor to GND on 4 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the SX1276.

What decoupling capacitors do designs use on the SX1276 VBAT_DIG_14 pin?

The VBAT_DIG_14 pin has a decoupling capacitor on 4 of 4 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the SX1276.

Which microcontrollers do boards using the SX1276 use?

Most are built on STM32 (3) and ESP32 (1).

How big is a typical board using the SX1276?

The median is 50 × 24.5 mm, and 0% are two-layer designs.

What is the most popular open source board using the SX1276?

By GitHub stars, TinyTracker by daveshah1, with 13 stars.

Can I simulate one of these boards using the SX1276 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part