5 open source boards using the TL431A
Real designs built with the TL431A, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
AVR-Transistor-Tester
Upcycle-Electronics
141 × 66 mm55 parts2LNo license49Hyper osci
finnff
70 × 50 mm42 parts2LGPL-3.01RP2040/RP2350
Sniffer
OpenRemise
30 × 61.6 mm44 parts2LCERN-OHL-W-2.00STM32
BMS
buglalis
103 × 57 mm192 parts4LNo license0Usbc power
SoukeyCircuits
30 × 79 mm41 parts2LGPL-3.055
How designs wire the TL431A
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TL431A connects to, and the resistors, capacitors and other passives placed on it.
- The K_1 pin has a series resistor on 3 of 5 designs, most often 8.2 kΩ (then 220 kΩ).
- The REF_2 pin has a series resistor on 3 of 5 designs, most often 1 kΩ (then 150 Ω).
- The A_3 pin has a series resistor on 3 of 5 designs, most often 10 kΩ (then 1 kΩ).
- The K_1 pin has a pull-up to VBUS on 2 of 5 designs, most often 6.8 kΩ (then 2.2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| K_1pin 1 | Connected to: Signal 100% |
|
| REF_2pin 2 | Connected to: Signal 60% · GND 40% |
|
| A_3pin 3 | Connected to: Signal 80% · GND 20% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Usbc power by SoukeyCircuits, AVR-Transistor-Tester by Upcycle-Electronics, Hyper osci by finnff and BMS by buglalis.
The TL431A in open source designs
The gallery holds 5 open source boards using the TL431A from 5 GitHub repositories; a typical one measures about 70 × 61.6 mm and carries around 44 components.
80% are two-layer designs, the rest use four layers or more, and 60% carry an open source license.
The most starred is Usbc power by SoukeyCircuits.
Microcontrollers on boards using the TL431A
What boards using the TL431A are built for
TL431A: common questions
Where can I find a TL431A reference design?
Each of the 5 boards on this page is a real design using the TL431A. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TL431A K_1 pin?
The K_1 pin has a series resistor on 3 of 5 designs, most often 8.2 kΩ (then 220 kΩ). Counted from the KiCad layouts of 5 open source designs using the TL431A.
What resistor goes on the TL431A REF_2 pin?
The REF_2 pin has a series resistor on 3 of 5 designs, most often 1 kΩ (then 150 Ω). Counted from the KiCad layouts of 5 open source designs using the TL431A.
What resistor goes on the TL431A A_3 pin?
The A_3 pin has a series resistor on 3 of 5 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 5 open source designs using the TL431A.
Which microcontrollers do boards using the TL431A use?
Most are built on AVR/Arduino (1), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the TL431A?
The median is 70 × 61.6 mm, and 80% are two-layer designs.
What is the most popular open source board using the TL431A?
By GitHub stars, Usbc power by SoukeyCircuits, with 55 stars.
Can I simulate one of these boards using the TL431A before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.