16 open source boards using the TL431BIDBZR
Real designs built with the TL431BIDBZR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Arduino ads129x
OpenElectronicsLab
197 × 71 mm267 partsGPL-3.0102Arpeggiator
EwoudVV
220 × 170 mm350 parts2LNo license1Mirte master bottom
mirte-robot
84.3 × 93.1 mm109 parts4LCERN-OHL-P-2.01After
DD1SB
180 × 140 mm287 parts2LMIT0ELARA two bucket PSU
MatejGomboc
150 × 90 mm99 parts2LCERN-OHL-W-2.05Before
DD1SB
180 × 140 mm287 parts2LMIT0AVR/Arduino
PID Board SMT
AaronDoubert
100 × 100 mm184 parts2LNo license0ESP32
Zone syntax test
gokcesena53
90 × 55 mm89 parts4LMIT0Dfm-2oz
DD1SB
180 × 140 mm287 parts2LMIT0Dfm special finish
DD1SB
180 × 140 mm287 parts2LMIT0E2-native
DD1SB
180 × 140 mm287 parts2LMIT0E4-native
DD1SB
180 × 140 mm287 parts2LMIT0E4R1-baseline
DD1SB
180 × 140 mm287 parts2LMIT0RF2M
DD1SB
150 × 110 mm287 parts2LMIT0Sliver only
DD1SB
180 × 140 mm287 parts2LMIT0Strict before
DD1SB
180 × 140 mm287 parts2LMIT0
How designs wire the TL431BIDBZR
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TL431BIDBZR connects to, and the resistors, capacitors and other passives placed on it.
- The REF pin has a resistor to GND on 5 of 7 designs, most often 19.6 kΩ (then 10 kΩ).
- The ANODE pin is tied to GND on 6 of 7 designs.
- The CATHODE pin has a series resistor on 4 of 7 designs, most often 1 kΩ (then 47 kΩ).
- The REF pin has a series resistor on 4 of 7 designs, most often 36.5 kΩ (then 330 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CATHODEpin 1 | Connected to: Signal 86% |
|
| REFpin 2 | Connected to: Signal 86% |
|
| ANODEpin 3 | Connected to: GND 86% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Arduino ads129x by OpenElectronicsLab, ELARA two bucket PSU by MatejGomboc, Arpeggiator by EwoudVV and Mirte master bottom by mirte-robot.
The TL431BIDBZR in open source designs
The gallery holds 16 open source boards using the TL431BIDBZR from 7 GitHub repositories; a typical one measures about 180 × 140 mm and carries around 287 components.
87% are two-layer designs, the rest use four layers or more, and 88% carry an open source license.
The most starred is Arduino ads129x by OpenElectronicsLab.
Parts used alongside the TL431BIDBZR
Microcontrollers on boards using the TL431BIDBZR
What boards using the TL431BIDBZR are built for
TL431BIDBZR: common questions
Where can I find a TL431BIDBZR reference design?
Each of the 16 boards on this page is a real design using the TL431BIDBZR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TL431BIDBZR REF pin?
The REF pin has a resistor to GND on 5 of 7 designs, most often 19.6 kΩ (then 10 kΩ). Counted from the KiCad layouts of 7 open source designs using the TL431BIDBZR.
How is the TL431BIDBZR ANODE pin connected?
The ANODE pin is tied to GND on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the TL431BIDBZR.
What resistor goes on the TL431BIDBZR CATHODE pin?
The CATHODE pin has a series resistor on 4 of 7 designs, most often 1 kΩ (then 47 kΩ). Counted from the KiCad layouts of 7 open source designs using the TL431BIDBZR.
Which microcontrollers do boards using the TL431BIDBZR use?
Most are built on AVR/Arduino (2) and ESP32 (1).
How big is a typical board using the TL431BIDBZR?
The median is 180 × 140 mm, and 87% are two-layer designs.
What is the most popular open source board using the TL431BIDBZR?
By GitHub stars, Arduino ads129x by OpenElectronicsLab, with 102 stars.
Can I simulate one of these boards using the TL431BIDBZR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.