9 open source boards using the TLP291-4
Real designs built with the TLP291-4, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Module do
andreili
89.5 × 62.2 mm133 parts2LGPL-3.066STM32
Mcu
trlsmax
92.6 × 62.8 mm92 parts2LGPL-3.04CameraTriggerSensorNodeOnly
chrocket
92.1 × 93.5 mm55 parts2LGPL-3.02STM32
Impeller18
buglalis
236.1 × 156.9 mm750 parts4LNo license0STM32
Placed
danhmanu
100 × 80 mm310 parts2LNo license0ESP32
ElevatorLift
Nickster44
90 × 90 mm113 parts4LNo license0STM32
Module di
andreili
89.5 × 62.2 mm116 parts2LGPL-3.066STM32
PLC STM32 Modbus
danhmanu
100 × 80 mm310 parts2LNo license0AVR/Arduino
Mega Controller
prasad73
285 × 174.6 mm113 parts2LNo license0
How designs wire the TLP291-4
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TLP291-4 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 14 has a pull-up to 3.3V on 3 of 7 designs, most often 10 kΩ (then 27 Ω).
- Pin 16 has a pull-up to 3.3V on 3 of 7 designs, most often 10 kΩ (then 27 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 14 | Connected to: A connector 29% |
|
| Pin 16 | Connected to: A connector 29% |
|
14 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Module di by andreili, Mcu by trlsmax, CameraTriggerSensorNodeOnly by chrocket and Impeller18 by buglalis.
The TLP291-4 in open source designs
The gallery holds 9 open source boards using the TLP291-4 from 7 GitHub repositories; a typical one measures about 92.6 × 80 mm and carries around 116 components.
78% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is Module do by andreili.
Parts used alongside the TLP291-4
Microcontrollers on boards using the TLP291-4
TLP291-4: common questions
Where can I find a TLP291-4 reference design?
Each of the 9 boards on this page is a real design using the TLP291-4. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the TLP291-4 pin 14?
Pin 14 has a pull-up to 3.3V on 3 of 7 designs, most often 10 kΩ (then 27 Ω). Counted from the KiCad layouts of 7 open source designs using the TLP291-4.
What pull-up resistor is used on the TLP291-4 pin 16?
Pin 16 has a pull-up to 3.3V on 3 of 7 designs, most often 10 kΩ (then 27 Ω). Counted from the KiCad layouts of 7 open source designs using the TLP291-4.
Which microcontrollers do boards using the TLP291-4 use?
Most are built on STM32 (6), AVR/Arduino (1) and ESP32 (1).
How big is a typical board using the TLP291-4?
The median is 92.6 × 80 mm, and 78% are two-layer designs.
What is the most popular open source board using the TLP291-4?
By GitHub stars, Module do by andreili, with 66 stars.
Can I simulate one of these boards using the TLP291-4 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.