7 open source boards using the TYPE-C-31-M-12
Real designs built with the TYPE-C-31-M-12, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Key ripper
bschwind
285.8 × 116.7 mm211 parts2LApache-2.0288ESP32
Nsec badge-2025
nsec
89 × 123.4 mm80 parts2LMIT61STM32
Ccd with stm32
RicardoSung
48.6 × 46.4 mm46 parts2LAGPL-3.01Nordic nRF
GPS-Tracker
zzertexx
65 × 38.5 mm71 parts4LNo license0ESP32
Nsec badge-2025-panel
nsec
197 × 249.7 mm80 parts2LMIT61Kicad pmxdalfin board2
faoziaziz
186 × 112.5 mm226 parts4LGPL-3.00ESP32
Nsec badge-2025-baseboard
nsec
150 × 70 mm42 parts2LMIT61
How designs wire the TYPE-C-31-M-12
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TYPE-C-31-M-12 connects to, and the resistors, capacitors and other passives placed on it.
- The CC1 pin has a resistor to GND on 5 of 5 designs, most often 5.1 kΩ (then 603 Ω).
- The CC2 pin has a resistor to GND on 5 of 5 designs, most often 5.1 kΩ (then 603 Ω).
- The SBU1 pin is left unconnected on 5 of 5 designs.
- The SBU2 pin is left unconnected on 5 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SHpin 0, 1, 2, 3 | Connected to: GND 67% · not connected 33% | — |
| GNDpin A1, A12, B1, B12 | Connected to: GND 100% | — |
| VBUSpin A4, A9, B4, B9 | Connected to: VBUS 100% | — |
| CC1pin A5 | Connected to: Signal 100% |
|
| SBU1pin A8 | Connected to: Not connected 100% | — |
| CC2pin B5 | Connected to: Signal 100% |
|
| SBU2pin B8 | Connected to: Not connected 100% | — |
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Key ripper by bschwind, Nsec badge-2025 by nsec, Ccd with stm32 by RicardoSung and Kicad pmxdalfin board2 by faoziaziz.
The TYPE-C-31-M-12 in open source designs
The gallery holds 7 open source boards using the TYPE-C-31-M-12 from 5 GitHub repositories; a typical one measures about 150 × 112.5 mm and carries around 80 components.
71% are two-layer designs, the rest use four layers or more, and 86% carry an open source license.
The most starred is Key ripper by bschwind.
Parts used alongside the TYPE-C-31-M-12
Microcontrollers on boards using the TYPE-C-31-M-12
What boards using the TYPE-C-31-M-12 are built for
TYPE-C-31-M-12: common questions
Where can I find a TYPE-C-31-M-12 reference design?
Each of the 7 boards on this page is a real design using the TYPE-C-31-M-12. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TYPE-C-31-M-12 CC1 pin?
The CC1 pin has a resistor to GND on 5 of 5 designs, most often 5.1 kΩ (then 603 Ω). Counted from the KiCad layouts of 5 open source designs using the TYPE-C-31-M-12.
What resistor goes on the TYPE-C-31-M-12 CC2 pin?
The CC2 pin has a resistor to GND on 5 of 5 designs, most often 5.1 kΩ (then 603 Ω). Counted from the KiCad layouts of 5 open source designs using the TYPE-C-31-M-12.
How is the TYPE-C-31-M-12 SBU1 pin connected?
The SBU1 pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TYPE-C-31-M-12.
Which microcontrollers do boards using the TYPE-C-31-M-12 use?
Most are built on ESP32 (3), Nordic nRF (1), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the TYPE-C-31-M-12?
The median is 150 × 112.5 mm, and 71% are two-layer designs.
What is the most popular open source board using the TYPE-C-31-M-12?
By GitHub stars, Key ripper by bschwind, with 288 stars.
Can I simulate one of these boards using the TYPE-C-31-M-12 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.