12 open source boards using the AP3015AKTR-G1
Real designs built with the AP3015AKTR-G1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Elector s-Tiny-Solar-Power-Supply
YUKESH0620
35 × 15 mm16 parts2LMIT1Tiny-Solar-Power-Supply
NitishSingh8
38.1 × 19.9 mm16 parts2LNo license0Klp5e tiny solar supply
futureshocked
42.5 × 17 mm16 parts2LMIT0Solar supply-
siddharthkote25
41.9 × 18.9 mm16 parts2LNo license0Tiny-Solar-Power-Supply-
SAKTHIVELB03
37.2 × 19.7 mm16 parts2LNo license0Task2
narimonjonmurodov
39.5 × 17.3 mm16 parts2LNo license0Tiny solar supply
Mo-Kara
36.9 × 16.9 mm16 parts2LNo license0Tiny Solar Supply
crisramil
35.8 × 20.4 mm16 parts2LNo license0Solar power supply
Reon-02
35.4 × 16.9 mm12 parts2LNo license0Ch02-blinky
futureshocked
21.8 × 20.3 mm8 parts2LMIT0Project-02-Solar-Power-Supply
Darshan7052006
39.1 × 20.3 mm16 parts2LNo license0Tiny Solar Supply
harris8099
40.2 × 18.6 mm16 parts2LNo license0
How designs wire the AP3015AKTR-G1
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the AP3015AKTR-G1 connects to, and the resistors, capacitors and other passives placed on it.
- The VIN pin has a capacitor to GND on 11 of 11 designs, most often 4.7 µF (then 10 nF).
- The SHDN pin has a series resistor on 10 of 11 designs, most often 10 kΩ.
- The VIN pin has a inductor on 10 of 11 designs, most often 10 µH.
- The VIN pin has a series resistor on 10 of 11 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SWpin 1 | Connected to: Signal 91% |
|
| GNDpin 2 | Connected to: GND 91% | — |
| FBpin 3 | Connected to: Signal 100% |
|
| SHDNpin 4 | Connected to: Signal 91% |
|
| VINpin 5 | Connected to: A connector 82% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Elector s-Tiny-Solar-Power-Supply-PCB by YUKESH0620, Tiny Solar Supply by crisramil, Project-02-Solar-Power-Supply by Darshan7052006 and Ch02-blinky by futureshocked.
The AP3015AKTR-G1 in open source designs
The gallery holds 12 open source boards using the AP3015AKTR-G1 from 11 GitHub repositories; a typical one measures about 37.6 × 18.8 mm and carries around 16 components.
100% are two-layer designs, the rest use four layers or more, and 25% carry an open source license.
The most starred is Elector s-Tiny-Solar-Power-Supply-PCB by YUKESH0620.
What boards using the AP3015AKTR-G1 are built for
AP3015AKTR-G1: common questions
Where can I find a AP3015AKTR-G1 reference design?
Each of the 12 boards on this page is a real design using the AP3015AKTR-G1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the AP3015AKTR-G1 VIN pin connected?
The VIN pin has a capacitor to GND on 11 of 11 designs, most often 4.7 µF (then 10 nF). Counted from the KiCad layouts of 11 open source designs using the AP3015AKTR-G1.
What resistor goes on the AP3015AKTR-G1 SHDN pin?
The SHDN pin has a series resistor on 10 of 11 designs, most often 10 kΩ. Counted from the KiCad layouts of 11 open source designs using the AP3015AKTR-G1.
How is the AP3015AKTR-G1 SW pin connected?
The SW pin has a inductor on 9 of 11 designs, most often 10 µH. Counted from the KiCad layouts of 11 open source designs using the AP3015AKTR-G1.
How big is a typical board using the AP3015AKTR-G1?
The median is 37.6 × 18.8 mm, and 100% are two-layer designs.
What is the most popular open source board using the AP3015AKTR-G1?
By GitHub stars, Elector s-Tiny-Solar-Power-Supply-PCB by YUKESH0620, with 1 stars.
Can I simulate one of these boards using the AP3015AKTR-G1 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.