16 open source boards using the ATMEGA32U2

Real designs built with the ATMEGA32U2, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

16 boardsClear filters|Most starred

How designs wire the ATMEGA32U2

Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the ATMEGA32U2 connects to, and the resistors, capacitors and other passives placed on it.

  • The XTAL1 pin has a capacitor to GND on 8 of 9 designs, most often 22 pF (then 18 pF).
  • The UCAP pin has a capacitor to GND on 8 of 8 designs, most often 1 µF (then 100 nF).
  • The D+ pin has a series resistor on 8 of 8 designs, most often 22 Ω.
  • The D- pin has a series resistor on 8 of 8 designs, most often 22 Ω.
XTAL1pin 1Connected to: Signal 100%
  • Capacitor to GND on 89% · 22 pF (4), 18 pF (3), 100 nF (2)
  • Crystal on 78% · 16 MHz (7)
PC0/XTAL2pin 2Connected to: Signal 100%
  • Crystal on 78% · 16 MHz (7)
  • Capacitor to GND on 78% · 22 pF (4), 18 pF (3)
GNDpin 3Connected to: GND 89%
VCCpin 4Connected to: VCC 89%
  • Decoupling capacitor on 56% · 100 nF (5), 4.7 µF (1), 1 µF (1)
HWB/PD7pin 13Connected to: Signal 100%
  • Resistor to GND on 44% · 10 kΩ (4)
PC1/RESETpin 24Connected to: A connector 44%
  • Pull-up to VCC on 67% · 10 kΩ (6)
UCAPpin 27Connected to: Signal 100%
  • Capacitor to GND on 100% · 1 µF (7), 100 nF (1)
UGNDpin 28Connected to: GND 100%
D+pin 29Connected to: Signal 100%
  • Series resistor on 100% · 22 Ω (8)
D-pin 30Connected to: Signal 100%
  • Series resistor on 100% · 22 Ω (8)
UVCCpin 31Connected to: VCC 100%
  • Decoupling capacitor on 50% · 100 nF (2), 4.7 µF (1), 1 µF (1)
AVCCpin 32Connected to: VCC 100%
  • Decoupling capacitor on 50% · 100 nF (3), 4.7 µF (1), 1 µF (1)

20 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Nt210 by evyd13, Amkey usb by BASLQC, Pcb by trebb and Keyboard by nicola-strappazzon.

The ATMEGA32U2 in open source designs

The gallery holds 16 open source boards using the ATMEGA32U2 from 9 GitHub repositories; a typical one measures about 102 × 43.3 mm and carries around 41 components.

93% are two-layer designs, the rest use four layers or more, and 56% carry an open source license.

The most starred is Nt210 by evyd13.

Microcontrollers on boards using the ATMEGA32U2

What boards using the ATMEGA32U2 are built for

ATMEGA32U2: common questions

Where can I find a ATMEGA32U2 reference design?

Each of the 16 boards on this page is a real design using the ATMEGA32U2. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the ATMEGA32U2 XTAL1 pin connected?

The XTAL1 pin has a capacitor to GND on 8 of 9 designs, most often 22 pF (then 18 pF). Counted from the KiCad layouts of 9 open source designs using the ATMEGA32U2.

How is the ATMEGA32U2 UCAP pin connected?

The UCAP pin has a capacitor to GND on 8 of 8 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 9 open source designs using the ATMEGA32U2.

What resistor goes on the ATMEGA32U2 D+ pin?

The D+ pin has a series resistor on 8 of 8 designs, most often 22 Ω. Counted from the KiCad layouts of 9 open source designs using the ATMEGA32U2.

Which microcontrollers do boards using the ATMEGA32U2 use?

Most are built on AVR/Arduino (15) and STM32 (1).

How big is a typical board using the ATMEGA32U2?

The median is 102 × 43.3 mm, and 93% are two-layer designs.

What is the most popular open source board using the ATMEGA32U2?

By GitHub stars, Nt210 by evyd13, with 56 stars.

Can I simulate one of these boards using the ATMEGA32U2 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part