5 open source boards using the ATMEGA8-P

Real designs built with the ATMEGA8-P, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the ATMEGA8-P

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ATMEGA8-P connects to, and the resistors, capacitors and other passives placed on it.

  • Pin 8 is tied to GND on 5 of 5 designs.
  • Pin 22 is tied to GND on 5 of 5 designs.
  • Pin 7 has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF).
  • Pin 9 has a crystal on 4 of 5 designs, most often 12 MHz (then 8 MHz).
Pin 1Connected to: Signal 80% · not connected 20%
  • Pull-up to VCC on 60% · 10 kΩ (3)
Pin 7Connected to: VCC 60% · a signal 40%
  • Decoupling capacitor on 80% · 100 nF (2), 10 µF (1)
  • Inductor on 40% · 10 mH (1)
Pin 8Connected to: GND 100%
Pin 9Connected to: Signal 100%
  • Crystal on 80% · 12 MHz (1), 8 MHz (1), 14.7456 MHz (1)
  • Capacitor to GND on 80% · 22 pF (2), 15 pF (1)
Pin 10Connected to: Signal 80% · not connected 20%
  • Crystal on 80% · 12 MHz (1), 8 MHz (1), 14.7456 MHz (1)
  • Capacitor to GND on 80% · 15 pF (1), 22 pF (1)
Pin 14Connected to: Signal 100%
  • Series resistor on 40% · 68 Ω (1), 10 kΩ (1)
Pin 15Connected to: Signal 100%
  • Series resistor on 40% · 68 Ω (1), 10 kΩ (1)
Pin 17Connected to: Signal 100%
  • Series resistor on 80% · 220 Ω (1), 10 kΩ (1), 100 Ω (1)
Pin 18Connected to: Signal 100%
  • Series resistor on 60% · 220 Ω (1), 10 kΩ (1), 100 Ω (1)
Pin 19Connected to: Signal 100%
  • Series resistor on 40% · 220 Ω (1), 10 kΩ (1)
Pin 20Connected to: VCC 60% · a signal 40%
  • Decoupling capacitor on 60% · 100 nF (1), 22 µF (1)
  • Inductor on 40% · 10 mH (1), 470 nH (1)
Pin 21Connected to: Not connected 40% · VCC 20% · a signal 40%
  • Capacitor to GND on 60% · 1 µF (1), 100 nF (1)
Pin 22Connected to: GND 100%
Pin 23Connected to: Signal 100%
  • Series resistor on 40% · 100 kΩ (1), 50 Ω (1)
Pin 27Connected to: Signal 60% · not connected 40%
  • Series resistor on 40% · 10 kΩ (1), 2.2 kΩ (1)
Pin 28Connected to: Signal 60% · not connected 40%
  • Series resistor on 40% · 10 kΩ (1), 2.2 kΩ (1)

12 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AVR-ZIF-Programmer by jbtronics, Hvpp big adapter by emard, WBO2 by rusefi and Main by qweqq.

The ATMEGA8-P in open source designs

The gallery holds 5 open source boards using the ATMEGA8-P from 5 GitHub repositories; a typical one measures about 158.8 × 65.7 mm and carries around 51 components.

100% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.

The most starred is AVR-ZIF-Programmer by jbtronics.

Microcontrollers on boards using the ATMEGA8-P

What boards using the ATMEGA8-P are built for

ATMEGA8-P: common questions

Where can I find a ATMEGA8-P reference design?

Each of the 5 boards on this page is a real design using the ATMEGA8-P. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the ATMEGA8-P pin 8 connected?

Pin 8 is tied to GND on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the ATMEGA8-P.

How is the ATMEGA8-P pin 22 connected?

Pin 22 is tied to GND on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the ATMEGA8-P.

What decoupling capacitors do designs use on the ATMEGA8-P pin 7?

Pin 7 has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the ATMEGA8-P.

Which microcontrollers do boards using the ATMEGA8-P use?

Most are built on AVR/Arduino (5).

How big is a typical board using the ATMEGA8-P?

The median is 158.8 × 65.7 mm, and 100% are two-layer designs.

What is the most popular open source board using the ATMEGA8-P?

By GitHub stars, AVR-ZIF-Programmer by jbtronics, with 12 stars.

Can I simulate one of these boards using the ATMEGA8-P before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part