7 open source boards using the ATTINY1616-S

Real designs built with the ATTINY1616-S, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the ATTINY1616-S

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the ATTINY1616-S connects to, and the resistors, capacitors and other passives placed on it.

  • The VCC pin has a decoupling capacitor on 6 of 7 designs, most often 100 nF (then 10 µF).
  • The PA7 pin has a series resistor on 3 of 7 designs, most often 330 Ω (then 22 Ω).
  • The PB1 pin has a series resistor on 3 of 7 designs, most often 330 Ω (then 4.7 kΩ).
  • The PB1 pin has a pull-up to VCC on 3 of 7 designs, most often 4.7 kΩ (then 10 kΩ).
VCCpin 1Connected to: 3.3V 86%
  • Decoupling capacitor on 86% · 100 nF (6), 10 µF (2), 4.7 µF (1)
PA7pin 5Connected to: Signal 57% · not connected 43%
  • Series resistor on 43% · 330 Ω (2), 22 Ω (1)
PB1pin 10Connected to: Signal 100%
  • Series resistor on 43% · 330 Ω (1), 4.7 kΩ (1), 1 kΩ (1)
  • Pull-up to VCC on 43% · 4.7 kΩ (2), 10 kΩ (1)
PC0pin 12Connected to: Signal 71% · not connected 29%
  • Series resistor on 43% · 330 Ω (1), 4.7 kΩ (1), 100 Ω (1)
PC1pin 13Connected to: Signal 71% · not connected 29%
  • Series resistor on 43% · 330 Ω (1), 4.7 kΩ (1), 100 Ω (1)
PC2pin 14Connected to: Signal 71% · not connected 29%
  • Series resistor on 43% · 330 Ω (1), 4.7 kΩ (1), 100 Ω (1)
PC3pin 15Connected to: Signal 57% · not connected 43%
  • Series resistor on 43% · 330 Ω (1), 4.7 kΩ (1), 100 Ω (1)
GNDpin 20Connected to: GND 100%

12 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include DekaLED PCB by anachrocomputer, PCB Business Card by Bumb1eris, Blynk by DynamicWhiteHat and Lightmeter by empdo.

The ATTINY1616-S in open source designs

The gallery holds 7 open source boards using the ATTINY1616-S from 7 GitHub repositories; a typical one measures about 80.5 × 53.8 mm and carries around 41 components.

86% are two-layer designs, the rest use four layers or more, and 14% carry an open source license.

The most starred is Night light-PCB-prototype by oyeniyihakeem08-blip.

Microcontrollers on boards using the ATTINY1616-S

What boards using the ATTINY1616-S are built for

ATTINY1616-S: common questions

Where can I find a ATTINY1616-S reference design?

Each of the 7 boards on this page is a real design using the ATTINY1616-S. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the ATTINY1616-S VCC pin?

The VCC pin has a decoupling capacitor on 6 of 7 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 7 open source designs using the ATTINY1616-S.

What resistor goes on the ATTINY1616-S PA7 pin?

The PA7 pin has a series resistor on 3 of 7 designs, most often 330 Ω (then 22 Ω). Counted from the KiCad layouts of 7 open source designs using the ATTINY1616-S.

What resistor goes on the ATTINY1616-S PB1 pin?

The PB1 pin has a series resistor on 3 of 7 designs, most often 330 Ω (then 4.7 kΩ). Counted from the KiCad layouts of 7 open source designs using the ATTINY1616-S.

Which microcontrollers do boards using the ATTINY1616-S use?

Most are built on AVR/Arduino (5), ESP32 (1) and STM32 (1).

How big is a typical board using the ATTINY1616-S?

The median is 80.5 × 53.8 mm, and 86% are two-layer designs.

What is the most popular open source board using the ATTINY1616-S?

By GitHub stars, Night light-PCB-prototype by oyeniyihakeem08-blip, with 0 stars.

Can I simulate one of these boards using the ATTINY1616-S before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part