5 open source boards using the BL0942
Real designs built with the BL0942, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
PCB Real-Time-Power-Monitoring-System-Development sensor
NguyenThanhHuy-debug
101.6 × 50.8 mm122 parts2LNo license2ESP32
Esp ev switch
valletw
99.9 × 58.4 mm78 parts4LMIT1ESP32
PLC4UNI
0sirys
102.4 × 83.1 mm207 parts4LMIT0ESP32
PLC4UNI
paulmartinezcuenta
5 × 5 mm177 parts4LMIT0Hw lower v2
oresk
102 × 104.8 mm96 parts4LNo license0
How designs wire the BL0942
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the BL0942 connects to, and the resistors, capacitors and other passives placed on it.
- The IP pin has a series resistor on 5 of 5 designs, most often 1 kΩ (then 510 Ω).
- The IN pin has a series resistor on 5 of 5 designs, most often 1 kΩ (then 510 Ω).
- The VP pin has a series resistor on 5 of 5 designs, most often 390 kΩ (then 510 Ω).
- The VDD pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 1 | Connected to: 3.3V 100% |
|
| IPpin 2 | Connected to: Signal 100% |
|
| INpin 3 | Connected to: Signal 100% |
|
| VPpin 4 | Connected to: Signal 100% |
|
| GNDpin 5 | Connected to: GND 80% · a signal 20% | — |
| CF1pin 6 | Connected to: Not connected 60% · a signal 40% | — |
| SELpin 7 | Connected to: GND 60% · not connected 20% · a signal 20% | — |
| SCLKpin 8 | Connected to: 3.3V 40% · GND 20% · a signal 40% |
|
| RX/SDIpin 9 | Connected to: ISO7021DR 40% |
|
| TX/SDOpin 10 | Connected to: ISO7021DR 40% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PCB Real-Time-Power-Monitoring-System-Development sensor by NguyenThanhHuy-debug, Esp ev switch by valletw, PLC4UNI by 0sirys and Hw lower v2 by oresk.
The BL0942 in open source designs
The gallery holds 5 open source boards using the BL0942 from 5 GitHub repositories; a typical one measures about 101.6 × 58.4 mm and carries around 122 components.
80% use four copper layers or more, and 60% carry an open source license.
The most starred is PCB Real-Time-Power-Monitoring-System-Development sensor by NguyenThanhHuy-debug.
Parts used alongside the BL0942
What boards using the BL0942 are built for
BL0942: common questions
Where can I find a BL0942 reference design?
Each of the 5 boards on this page is a real design using the BL0942. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the BL0942 IP pin?
The IP pin has a series resistor on 5 of 5 designs, most often 1 kΩ (then 510 Ω). Counted from the KiCad layouts of 5 open source designs using the BL0942.
What resistor goes on the BL0942 IN pin?
The IN pin has a series resistor on 5 of 5 designs, most often 1 kΩ (then 510 Ω). Counted from the KiCad layouts of 5 open source designs using the BL0942.
What resistor goes on the BL0942 VP pin?
The VP pin has a series resistor on 5 of 5 designs, most often 390 kΩ (then 510 Ω). Counted from the KiCad layouts of 5 open source designs using the BL0942.
What parts are used alongside the BL0942?
The ADS1115IDGS, AT3H4B-CuH-S, ESP32-S3-WROOM-1, GP8211S-TC50-EW and GP8302-TC50-EW appear in the most repositories here.
Which microcontrollers do boards using the BL0942 use?
Most are built on ESP32 (3) and STM32 (1).
How big is a typical board using the BL0942?
The median is 101.6 × 58.4 mm, and 20% are two-layer designs.
What is the most popular open source board using the BL0942?
By GitHub stars, PCB Real-Time-Power-Monitoring-System-Development sensor by NguyenThanhHuy-debug, with 2 stars.
Can I simulate one of these boards using the BL0942 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.