12 open source boards using the C12084
Real designs built with the C12084, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Hex master motor control circuit
csiz
64 × 86 mm236 parts4LMIT9STM32
Driva x2
owennewo
100 × 67 mm147 parts4LNo license9- schematic only · 68 partsRP2040/RP2350
IGV1-16 Driver Backpack
Architeuthis-Flux
68 partsNo license6 STM32
RyanShalini SmartPDM
LHRIC
149.7 × 158.4 mm235 parts4LNo license2ESP32
SisuAssistant
Cadburies
66.5 × 70 mm155 parts4LApache-2.01STM32
PDM v3.0 - Top MCU
LHRIC
133.2 × 90.6 mm193 parts4LNo license2STM32
Megaboard Front V3
Kolmanpg
152.4 × 88.9 mm195 parts4LNo license0ESP32
Megaboard Rear V3
Kolmanpg
155.3 × 110.3 mm180 parts4LNo license0STM32
TCM STM32F302C8T6 - Breakout Board
LHRIC
113.8 × 74.9 mm58 parts2LNo license2PDM 2024 TestBoard - Tyler
LHRIC
67.1 × 46.2 mm43 parts4LNo license2PDM 2024 TestBoard
LHRIC
64 × 58 mm38 parts4LNo license2Power Logic Test Board
LHRIC
42.4 × 70.1 mm37 parts2LNo license2
How designs wire the C12084
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the C12084 connects to, and the resistors, capacitors and other passives placed on it.
- The CANH_7 pin has a series resistor on 4 of 5 designs, most often 120 Ω.
- The VCC_3 pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF (then 2.2 µF).
- The VREF_5 pin has a capacitor to GND on 2 of 5 designs, most often 100 nF.
- The CANL_6 pin has a series resistor on 2 of 5 designs, most often 120 Ω.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GND_2pin 2 | Connected to: GND 80% · a signal 20% | — |
| VCC_3pin 3 | Connected to: 3.3V 100% |
|
| VREF_5pin 5 | Connected to: Not connected 40% · 3.3V 40% · a signal 20% |
|
| CANL_6pin 6 | Connected to: A connector 40% |
|
| CANH_7pin 7 | Connected to: A connector 40% |
|
| RS_8pin 8 | Connected to: GND 40% · 5V 20% · a signal 40% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Hex master motor control circuit by csiz, Driva x2 by owennewo, PDM 2024 TestBoard by LHRIC and SisuAssistant by Cadburies.
The C12084 in open source designs
The gallery holds 12 open source boards using the C12084 from 6 GitHub repositories; a typical one measures about 100 × 74.9 mm and carries around 151 components.
82% use four copper layers or more, and 17% carry an open source license.
The most starred is Hex master motor control circuit by csiz.
Parts used alongside the C12084
Microcontrollers on boards using the C12084
What boards using the C12084 are built for
C12084: common questions
Where can I find a C12084 reference design?
Each of the 12 boards on this page is a real design using the C12084. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the C12084 CANH_7 pin?
The CANH_7 pin has a series resistor on 4 of 5 designs, most often 120 Ω. Counted from the KiCad layouts of 5 open source designs using the C12084.
What decoupling capacitors do designs use on the C12084 VCC_3 pin?
The VCC_3 pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF (then 2.2 µF). Counted from the KiCad layouts of 5 open source designs using the C12084.
How is the C12084 VREF_5 pin connected?
The VREF_5 pin has a capacitor to GND on 2 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the C12084.
Which microcontrollers do boards using the C12084 use?
Most are built on STM32 (5), ESP32 (3) and RP2040/RP2350 (1).
How big is a typical board using the C12084?
The median is 100 × 74.9 mm, and 18% are two-layer designs.
What is the most popular open source board using the C12084?
By GitHub stars, Hex master motor control circuit by csiz, with 9 stars.
Can I simulate one of these boards using the C12084 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.