5 open source boards using the C29981
Real designs built with the C29981, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Twomes opentherm monitor hardware
energietransitie
31.1 × 34.5 mm28 parts2LCERN-OHL-P-2.03Twomes opentherm monitor hardware
energiegedrag-nl
31.1 × 34.5 mm28 parts2LCERN-OHL-P-2.00RP2040/RP2350
Supercap
Twisted-Fields
109 × 155.5 mm184 parts4LNo license81ESP32
Megaboard Rear V3
Kolmanpg
155.3 × 110.3 mm180 parts4LNo license0NewKicadProject
henkjannl
46.5 × 18.5 mm17 parts2LMIT1
How designs wire the C29981
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the C29981 connects to, and the resistors, capacitors and other passives placed on it.
- The AN pin has a series resistor on 3 of 5 designs, most often 1 kΩ.
- The CAT pin is tied to GND on 3 of 5 designs (a signal on 2).
- The COL pin is tied to VCC on 3 of 5 designs (a signal on 2).
- The AN pin has a pull-up to 5V on 2 of 5 designs, most often 120 Ω (then 1.2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ANpin 1 | Connected to: Signal 100% |
|
| CATpin 2 | Connected to: GND 60% · a signal 40% | — |
| EMpin 3 | Connected to: A connector 40% · GND 40% |
|
| COLpin 4 | Connected to: VCC 60% · a signal 40% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Supercap by Twisted-Fields, Twomes opentherm monitor hardware by energietransitie, NewKicadProject by henkjannl and Twomes opentherm monitor hardware by energiegedrag-nl.
The C29981 in open source designs
The gallery holds 5 open source boards using the C29981 from 5 GitHub repositories; a typical one measures about 46.5 × 34.5 mm and carries around 28 components.
60% are two-layer designs, the rest use four layers or more, and 60% carry an open source license.
The most starred is Supercap by Twisted-Fields.
Parts used alongside the C29981
Microcontrollers on boards using the C29981
What boards using the C29981 are built for
C29981: common questions
Where can I find a C29981 reference design?
Each of the 5 boards on this page is a real design using the C29981. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the C29981 AN pin?
The AN pin has a series resistor on 3 of 5 designs, most often 1 kΩ. Counted from the KiCad layouts of 5 open source designs using the C29981.
How is the C29981 CAT pin connected?
The CAT pin is tied to GND on 3 of 5 designs (a signal on 2). Counted from the KiCad layouts of 5 open source designs using the C29981.
How is the C29981 COL pin connected?
The COL pin is tied to VCC on 3 of 5 designs (a signal on 2). Counted from the KiCad layouts of 5 open source designs using the C29981.
Which microcontrollers do boards using the C29981 use?
Most are built on ESP32 (1) and RP2040/RP2350 (1).
How big is a typical board using the C29981?
The median is 46.5 × 34.5 mm, and 60% are two-layer designs.
What is the most popular open source board using the C29981?
By GitHub stars, Supercap by Twisted-Fields, with 81 stars.
Can I simulate one of these boards using the C29981 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.