16 open source boards using the LM393DR2G
Real designs built with the LM393DR2G, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AWG DHO8-900
MatthiasElectronic
58 × 77.4 mm200 parts4LCERN-OHL-W-2.0215Coco salt replacement
qbancoffee
27.6 × 34.3 mm20 parts2LGPL-3.011Twomes opentherm monitor hardware
energietransitie
31.1 × 34.5 mm28 parts2LCERN-OHL-P-2.03STM32
Rabbit 2.0 body board (deck 2)
seralexeev
120.5 × 269.9 mm323 parts4LNo license1FPGA
SEM hitachi-
Serhio4522
100 × 70 mm284 parts4LNo license1ESP32
CAN-HBC-S3
ViktorNfa
70 × 50 mm160 parts4LNo license1ESP32
Lfp
maxakash
216 × 146 mm831 parts2LNo license0Raspberry Pi
1.2
tomrodinger
46.2 × 30.9 mm86 parts2LApache-2.00EEE3088F HAT
rb-jones
96 × 70 mm68 parts2LCC-BY-4.00ESP32
Panasonic intellibalance esphome
lukewaite
110 × 56 mm55 parts2LNo license0RP2040/RP2350
Sniffer
OpenRemise
30 × 61.6 mm44 parts2LCERN-OHL-W-2.00Twomes opentherm monitor hardware
energiegedrag-nl
31.1 × 34.5 mm28 parts2LCERN-OHL-P-2.00- schematic only · 9 partsESP32
RepeaterDMX
llextv
9 partsNo license0 Raspberry Pi
V9
tomrodinger
46.7 × 30.9 mm76 parts2LApache-2.00Raspberry Pi
1.1
tomrodinger
46.2 × 30.9 mm75 parts2LApache-2.00Raspberry Pi
Uw rs485 hat-V5
tomrodinger
46.7 × 30.9 mm53 parts2LApache-2.00
How designs wire the LM393DR2G
Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the LM393DR2G connects to, and the resistors, capacitors and other passives placed on it.
- The - pins have a resistor to GND on 10 of 12 designs, most often 100 kΩ (then 10 kΩ).
- The + pins have a series resistor on 10 of 12 designs, most often 18 kΩ (then 220 kΩ).
- The - pins have a series resistor on 9 of 12 designs, most often 10 kΩ (then 100 kΩ).
- The + pins have a resistor to GND on 9 of 12 designs, most often 10 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUT/A_1pin 1 | Connected to: Signal 100% |
|
| -pin 2, 6 | Connected to: Signal 83% |
|
| +pin 3, 5 | Connected to: Signal 75% |
|
| V-pin 4 | Connected to: GND 83% · 6.5V 17% | — |
| OUT/B_7pin 7 | Connected to: Not connected 50% · a signal 50% |
|
| V+pin 8 | Connected to: 5V 75% · a signal 25% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AWG DHO8-900 by MatthiasElectronic, Coco salt replacement by qbancoffee, Twomes opentherm monitor hardware by energietransitie and Rabbit 2.0 body board (deck 2) by seralexeev.
The LM393DR2G in open source designs
The gallery holds 16 open source boards using the LM393DR2G from 13 GitHub repositories; a typical one measures about 46.7 × 50 mm and carries around 72 components.
73% are two-layer designs, the rest use four layers or more, and 63% carry an open source license.
The most starred is AWG DHO8-900 by MatthiasElectronic.
Parts used alongside the LM393DR2G
Microcontrollers on boards using the LM393DR2G
What boards using the LM393DR2G are built for
LM393DR2G: common questions
Where can I find a LM393DR2G reference design?
Each of the 16 boards on this page is a real design using the LM393DR2G. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LM393DR2G - pin?
The - pins have a resistor to GND on 10 of 12 designs, most often 100 kΩ (then 10 kΩ). Counted from the KiCad layouts of 12 open source designs using the LM393DR2G.
What resistor goes on the LM393DR2G + pin?
The + pins have a series resistor on 10 of 12 designs, most often 18 kΩ (then 220 kΩ). Counted from the KiCad layouts of 12 open source designs using the LM393DR2G.
How is the LM393DR2G V- pin connected?
The V- pin is tied to GND on 10 of 12 designs (6.5V on 2). Counted from the KiCad layouts of 12 open source designs using the LM393DR2G.
What parts are used alongside the LM393DR2G?
The AMS1117-3.3, C29981, HT7550-1 and NE5532DR appear in the most repositories here.
Which microcontrollers do boards using the LM393DR2G use?
Most are built on ESP32 (4), Raspberry Pi (4), FPGA (1) and RP2040/RP2350 (1).
How big is a typical board using the LM393DR2G?
The median is 46.7 × 50 mm, and 73% are two-layer designs.
What is the most popular open source board using the LM393DR2G?
By GitHub stars, AWG DHO8-900 by MatthiasElectronic, with 215 stars.
Can I simulate one of these boards using the LM393DR2G before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.