5 open source boards using the FM2113
Real designs built with the FM2113, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Blinkekatze
TobleMiner
83 × 83 mm106 parts4LNo license34ESP32
OBSPro
FabianSchwartau
64 × 77 mm117 parts4LLGPL-2.13Poweroid
Prismary
98 × 78.8 mm56 parts2LCC-BY-NC-4.02STM32
Ultrasonic water depth measurement
ts01af
100 × 100 mm92 parts2LNo license0Lipo-Charger-Board
DevinJM3
36.3 × 36 mm32 parts4LMIT0
How designs wire the FM2113
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the FM2113 connects to, and the resistors, capacitors and other passives placed on it.
- The CS pin has a resistor to GND on 5 of 5 designs, most often 2 kΩ (then 1 kΩ).
- The VDD pin has a series capacitor on 5 of 5 designs, most often 100 nF (then 10 µF).
- The VSS pin has a series capacitor on 5 of 5 designs, most often 100 nF (then 10 µF).
- The VDD pin has a pull-up to BATT on 4 of 5 designs, most often 100 Ω (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CSpin 2 | Connected to: Signal 100% |
|
| NCpin 4 | Connected to: Not connected 100% | — |
| VDDpin 5 | Connected to: Signal 100% |
|
| VSSpin 6 | Connected to: A connector 60% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Blinkekatze by TobleMiner, OBSPro by FabianSchwartau, Poweroid by Prismary and Lipo-Charger-Board by DevinJM3.
The FM2113 in open source designs
The gallery holds 5 open source boards using the FM2113 from 5 GitHub repositories; a typical one measures about 83 × 78.8 mm and carries around 92 components.
60% use four copper layers or more, and 40% carry an open source license.
The most starred is Blinkekatze by TobleMiner.
What boards using the FM2113 are built for
FM2113: common questions
Where can I find a FM2113 reference design?
Each of the 5 boards on this page is a real design using the FM2113. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the FM2113 CS pin?
The CS pin has a resistor to GND on 5 of 5 designs, most often 2 kΩ (then 1 kΩ). Counted from the KiCad layouts of 5 open source designs using the FM2113.
How is the FM2113 VDD pin connected?
The VDD pin has a series capacitor on 5 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the FM2113.
How is the FM2113 VSS pin connected?
The VSS pin has a series capacitor on 5 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the FM2113.
Which microcontrollers do boards using the FM2113 use?
Most are built on ESP32 (2) and STM32 (1).
How big is a typical board using the FM2113?
The median is 83 × 78.8 mm, and 40% are two-layer designs.
What is the most popular open source board using the FM2113?
By GitHub stars, Blinkekatze by TobleMiner, with 34 stars.
Can I simulate one of these boards using the FM2113 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.