5 open source boards using the INA126
Real designs built with the INA126, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Pressure rev2
CohenLabPrinceton
65 × 56 mm17 parts2LGPL-3.015Arduino weatherstation
AGVOLUTION
125 × 85 mm64 parts2LNo license2NXP
Head
jsvana
73 × 43.8 mm41 parts2LMIT0ESP32
HridayMitra
aadityaa0523
70 × 50 mm31 parts2LMIT0Strain gauges
waterloo-rocketry
97.8 × 54.6 mm37 parts2LNo license5
How designs wire the INA126
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the INA126 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 5 of 5 designs, most often 150 Ω (then 16 kΩ).
- Pin 8 has a series resistor on 5 of 5 designs, most often 150 Ω (then 16 kΩ).
- Pin 7 is tied to 5V on 5 of 5 designs.
- Pin 7 has a decoupling capacitor on 3 of 5 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| Pin 4 | Connected to: GND 60% · -5V 20% · a signal 20% |
|
| Pin 5 | Connected to: GND 60% · 0.6V 40% | — |
| Pin 7 | Connected to: 5V 100% |
|
| Pin 8 | Connected to: Signal 100% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Pressure rev2 by CohenLabPrinceton, Strain gauges by waterloo-rocketry, Arduino weatherstation by AGVOLUTION and HridayMitra by aadityaa0523.
The INA126 in open source designs
The gallery holds 5 open source boards using the INA126 from 5 GitHub repositories; a typical one measures about 73 × 54.6 mm and carries around 37 components.
100% are two-layer designs, the rest use four layers or more, and 60% carry an open source license.
The most starred is Pressure rev2 by CohenLabPrinceton.
What boards using the INA126 are built for
INA126: common questions
Where can I find a INA126 reference design?
Each of the 5 boards on this page is a real design using the INA126. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the INA126 pin 1?
Pin 1 has a series resistor on 5 of 5 designs, most often 150 Ω (then 16 kΩ). Counted from the KiCad layouts of 5 open source designs using the INA126.
What resistor goes on the INA126 pin 8?
Pin 8 has a series resistor on 5 of 5 designs, most often 150 Ω (then 16 kΩ). Counted from the KiCad layouts of 5 open source designs using the INA126.
How is the INA126 pin 7 connected?
Pin 7 is tied to 5V on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the INA126.
Which microcontrollers do boards using the INA126 use?
Most are built on ESP32 (1) and NXP (1).
How big is a typical board using the INA126?
The median is 73 × 54.6 mm, and 100% are two-layer designs.
What is the most popular open source board using the INA126?
By GitHub stars, Pressure rev2 by CohenLabPrinceton, with 15 stars.
Can I simulate one of these boards using the INA126 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.