5 open source boards using the IST8310

Real designs built with the IST8310, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the IST8310

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the IST8310 connects to, and the resistors, capacitors and other passives placed on it.

  • The NC_3 pin is left unconnected on 5 of 5 designs.
  • The S1_4 pin is left unconnected on 5 of 5 designs.
  • The NC_7 pin is left unconnected on 5 of 5 designs.
  • The SETP_8 pin is left unconnected on 5 of 5 designs.
SCL_1pin 1Connected to: The microcontroller 80%, a connector 40%
  • Pull-up to 3.3V on 60% · 4.7 kΩ (2), 5.1 kΩ (1)
  • Series resistor on 40% · 22 Ω (1), 1.5 kΩ (1), 100 Ω (1)
VDD_2pin 2Connected to: 3.3V 80% · a signal 20%
  • Decoupling capacitor on 80% · 100 nF (11), 2.2 µF (1)
NC_3pin 3Connected to: Not connected 100%
S1_4pin 4Connected to: Not connected 100%
NC_5pin 5Connected to: Not connected 60% · GND 20% · a signal 20%
NC_6pin 6Connected to: Not connected 60% · GND 20% · a signal 20%
NC_7pin 7Connected to: Not connected 100%
SETP_8pin 8Connected to: Not connected 100%
GND_9pin 9Connected to: GND 100%
C1_10pin 10Connected to: Signal 80% · not connected 20%
  • Capacitor to GND on 80% · 4.7 µF (4)
GND_11pin 11Connected to: GND 100%
SETC_12pin 12Connected to: Not connected 100%
VDDIO_13pin 13Connected to: 3.3V 80% · a signal 20%
  • Decoupling capacitor on 80% · 100 nF (11), 2.2 µF (1)
NC_14pin 14Connected to: 3.3V 40% · not connected 20% · a signal 40%
  • Capacitor to GND on 40% · 100 nF (3)
DRDY_15pin 15Connected to: Not connected 80% · a signal 20%
SDA_16pin 16Connected to: The microcontroller 80%, a connector 40%
  • Pull-up to 3.3V on 60% · 4.7 kΩ (2), 5.1 kΩ (1)
  • Series resistor on 40% · 22 Ω (1), 1.5 kΩ (1), 100 Ω (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include LEVIA-H7 by piecol, Upper board by Peize-Liu, 350 Flight controller by ThaoMinhHoang and KHATAF-F411 by xXsenseiXx.

The IST8310 in open source designs

The gallery holds 5 open source boards using the IST8310 from 5 GitHub repositories; a typical one measures about 51.9 × 50 mm and carries around 120 components.

80% use four copper layers or more, and 40% carry an open source license.

The most starred is LEVIA-H7 by piecol.

Parts used alongside the IST8310

Microcontrollers on boards using the IST8310

What boards using the IST8310 are built for

IST8310: common questions

Where can I find a IST8310 reference design?

Each of the 5 boards on this page is a real design using the IST8310. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the IST8310 NC_3 pin connected?

The NC_3 pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the IST8310.

How is the IST8310 S1_4 pin connected?

The S1_4 pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the IST8310.

How is the IST8310 NC_7 pin connected?

The NC_7 pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the IST8310.

Which microcontrollers do boards using the IST8310 use?

Most are built on STM32 (4).

How big is a typical board using the IST8310?

The median is 51.9 × 50 mm, and 20% are two-layer designs.

What is the most popular open source board using the IST8310?

By GitHub stars, LEVIA-H7 by piecol, with 68 stars.

Can I simulate one of these boards using the IST8310 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part