6 open source boards using the LM27761
Real designs built with the LM27761, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
SPINC
CoretechR
70 × 72 mm91 parts4LGPL-3.0463Freesample
azonenberg
124 × 190 mm566 parts8LBSD-3-Clause10USAYPT2026 FlashSensor MLWGS
williamlin108
100 × 60 mm68 parts4LNo license1ESP32
Phenobottle sensorboard
Flynsky
84.4 × 68.2 mm148 parts4LNo license0STM32
Monitor
rcls
35.5 × 33.7 mm61 parts4LNo license0Bpsk modulator
MTalon63
66.5 × 42 mm62 parts2LCustom license2
How designs wire the LM27761
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LM27761 connects to, and the resistors, capacitors and other passives placed on it.
- The CPOUT pin has a capacitor to GND on 6 of 6 designs, most often 4.7 µF (then 10 µF).
- The C- pin has a series capacitor on 6 of 6 designs, most often 1 µF.
- The C+ pin has a series capacitor on 6 of 6 designs, most often 1 µF.
- The VIN pin has a decoupling capacitor on 5 of 6 designs, most often 4.7 µF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VINpin 1 | Connected to: 5V 100% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| CPOUTpin 3 | Connected to: Signal 100% |
|
| VOUTpin 4 | Connected to: 3.3V 83% · a signal 17% |
|
| VFBpin 5 | Connected to: Signal 67% · 5V 33% |
|
| ENpin 6 | Connected to: 3.3V 83% · a signal 17% | — |
| C-pin 7 | Connected to: Signal 100% |
|
| C+pin 8 | Connected to: Signal 100% |
|
| PADpin 9 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include SPINC by CoretechR, Freesample by azonenberg, Bpsk modulator by MTalon63 and USAYPT2026 FlashSensor MLWGS by williamlin108.
The LM27761 in open source designs
The gallery holds 6 open source boards using the LM27761 from 6 GitHub repositories; a typical one measures about 77.2 × 64.1 mm and carries around 80 components.
83% use four copper layers or more, and 33% carry an open source license.
The most starred is SPINC by CoretechR.
Microcontrollers on boards using the LM27761
What boards using the LM27761 are built for
LM27761: common questions
Where can I find a LM27761 reference design?
Each of the 6 boards on this page is a real design using the LM27761. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM27761 CPOUT pin connected?
The CPOUT pin has a capacitor to GND on 6 of 6 designs, most often 4.7 µF (then 10 µF). Counted from the KiCad layouts of 6 open source designs using the LM27761.
How is the LM27761 C- pin connected?
The C- pin has a series capacitor on 6 of 6 designs, most often 1 µF. Counted from the KiCad layouts of 6 open source designs using the LM27761.
How is the LM27761 C+ pin connected?
The C+ pin has a series capacitor on 6 of 6 designs, most often 1 µF. Counted from the KiCad layouts of 6 open source designs using the LM27761.
Which microcontrollers do boards using the LM27761 use?
Most are built on ESP32 (1), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the LM27761?
The median is 77.2 × 64.1 mm, and 17% are two-layer designs.
What is the most popular open source board using the LM27761?
By GitHub stars, SPINC by CoretechR, with 463 stars.
Can I simulate one of these boards using the LM27761 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.