6 open source boards using the LM350_TO220
Real designs built with the LM350_TO220, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Controller
profdc9
100 × 100 mm180 parts2LNo license59ESP32
ThermovitalSync
emiirkaya
60 × 70 mm96 parts4LMIT2- schematic only · 64 parts
Squarely
Broosky
64 partsNo license2 Eurorack psu
jojo-monk
203.8 × 88.6 mm42 parts2LNo license1Shield
jesuscuadrul2
102 × 115.1 mm37 parts2LNo license1AC TO DC CONVERTER-15V-2A
AnshumanSingh2008
71.1 × 61 mm17 parts2LNo license0
How designs wire the LM350_TO220
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the LM350_TO220 connects to, and the resistors, capacitors and other passives placed on it.
- The VI pin has a capacitor to GND on 4 of 5 designs, most often 100 nF (then 100 µF).
- The ADJ pin has a series resistor on 3 of 5 designs, most often 120 Ω (then 1.8 kΩ).
- The ADJ pin has a resistor to GND on 2 of 5 designs, most often 1 kΩ.
- The ADJ pin has a pull-up to 5V on 2 of 5 designs, most often 330 Ω (then 220 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ADJpin 1 | Connected to: Signal 100% |
|
| VOpin 2 | Connected to: 12V 60% · a signal 40% | — |
| VIpin 3 | Connected to: Signal 80% · 12V 20% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Controller by profdc9, ThermovitalSync-PCB by emiirkaya, Shield by jesuscuadrul2 and Eurorack psu by jojo-monk.
The LM350_TO220 in open source designs
The gallery holds 6 open source boards using the LM350_TO220 from 6 GitHub repositories; a typical one measures about 100 × 88.6 mm and carries around 53 components.
80% are two-layer designs, the rest use four layers or more, and 17% carry an open source license.
The most starred is Controller by profdc9.
Microcontrollers on boards using the LM350_TO220
What boards using the LM350_TO220 are built for
LM350_TO220: common questions
Where can I find a LM350_TO220 reference design?
Each of the 6 boards on this page is a real design using the LM350_TO220. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM350_TO220 VI pin connected?
The VI pin has a capacitor to GND on 4 of 5 designs, most often 100 nF (then 100 µF). Counted from the KiCad layouts of 5 open source designs using the LM350_TO220.
What resistor goes on the LM350_TO220 ADJ pin?
The ADJ pin has a series resistor on 3 of 5 designs, most often 120 Ω (then 1.8 kΩ). Counted from the KiCad layouts of 5 open source designs using the LM350_TO220.
Which microcontrollers do boards using the LM350_TO220 use?
Most are built on ESP32 (1).
How big is a typical board using the LM350_TO220?
The median is 100 × 88.6 mm, and 80% are two-layer designs.
What is the most popular open source board using the LM350_TO220?
By GitHub stars, Controller by profdc9, with 59 stars.
Can I simulate one of these boards using the LM350_TO220 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.