9 open source boards using the LMC6482
Real designs built with the LMC6482, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Themis
F6ITU
100 × 50 mm29 parts2LNo license2AVR/Arduino
IR remote controlled amplifier main board
ak1211
159 × 100 mm123 parts2LMIT112V 6V3 Delay
FordPrfkt
160 × 100 mm111 parts2LNo license1Telemaque
f5bmi
100 × 50 mm78 parts2LNo license1Kicad introduction
wuespace
40.6 × 31.8 mm9 parts2LCC-BY-4.00Vswr extension bridge route
OE9SAU
83.7 × 37 mm50 parts2LNo license4TA
Tanmayeers
66 × 40 mm17 parts2LNo license1Vswr extension bridge
OE9SAU
84 × 37 mm49 parts2LNo license4Vswr
OE9SAU
37 × 74 mm34 parts2LNo license4
How designs wire the LMC6482
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the LMC6482 connects to, and the resistors, capacitors and other passives placed on it.
- The V- pin is tied to GND on 7 of 7 designs.
- Pin 1 has a series resistor on 5 of 7 designs, most often 1 kΩ (then 100 Ω).
- The - pins have a series resistor on 4 of 7 designs, most often 10 kΩ (then 4.12 kΩ).
- The + pins have a capacitor to GND on 4 of 7 designs, most often 100 nF (then 10 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: A connector 29% |
|
| -pin 2, 6 | Connected to: Signal 93% |
|
| +pin 3, 5 | Connected to: Signal 79% · GND 21% |
|
| V-pin 4 | Connected to: GND 100% | — |
| Pin 7 | Connected to: A connector 29% |
|
| V+pin 8 | Connected to: 12V 86% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Vswr by OE9SAU, Themis by F6ITU, IR remote controlled amplifier main board by ak1211 and Telemaque by f5bmi.
The LMC6482 in open source designs
The gallery holds 9 open source boards using the LMC6482 from 7 GitHub repositories; a typical one measures about 84 × 50 mm and carries around 49 components.
100% are two-layer designs, the rest use four layers or more, and 22% carry an open source license.
The most starred is Vswr extension bridge route by OE9SAU.
Microcontrollers on boards using the LMC6482
What boards using the LMC6482 are built for
LMC6482: common questions
Where can I find a LMC6482 reference design?
Each of the 9 boards on this page is a real design using the LMC6482. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LMC6482 V- pin connected?
The V- pin is tied to GND on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the LMC6482.
What resistor goes on the LMC6482 pin 1?
Pin 1 has a series resistor on 5 of 7 designs, most often 1 kΩ (then 100 Ω). Counted from the KiCad layouts of 7 open source designs using the LMC6482.
What resistor goes on the LMC6482 - pin?
The - pins have a series resistor on 4 of 7 designs, most often 10 kΩ (then 4.12 kΩ). Counted from the KiCad layouts of 7 open source designs using the LMC6482.
Which microcontrollers do boards using the LMC6482 use?
Most are built on AVR/Arduino (1).
How big is a typical board using the LMC6482?
The median is 84 × 50 mm, and 100% are two-layer designs.
What is the most popular open source board using the LMC6482?
By GitHub stars, Vswr extension bridge route by OE9SAU, with 4 stars.
Can I simulate one of these boards using the LMC6482 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.