6 open source boards using the LMR14050
Real designs built with the LMR14050, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
TFSBEC01
ThunderFly-aerospace
45 × 30 mm38 parts2LGPL-3.05LION2CELL02
mlab-modules
80.8 × 60.5 mm96 parts2LGPL-3.01ESP32
Seebum
peedrooh
65 × 56 mm91 parts4LNo license1LMR14050
qwerty1192
36.7 × 17.2 mm21 parts6LCERN-OHL-W-2.00LMR1405001
mlab-modules
52.8 × 52.8 mm20 parts2LGPL-3.00STM32
Power Board
SSL-A-Team
90 × 92.5 mm192 parts6LMIT6
How designs wire the LMR14050
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LMR14050 connects to, and the resistors, capacitors and other passives placed on it.
- The BOOT pin has a series capacitor on 6 of 6 designs, most often 100 nF.
- The VIN pin has a decoupling capacitor on 6 of 6 designs, most often 10 µF (then 100 nF).
- The RT/SYNC pin has a resistor to GND on 6 of 6 designs, most often 133 kΩ (then 59 kΩ).
- The FB pin has a resistor to GND on 6 of 6 designs, most often 10 kΩ (then 17.8 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| BOOTpin 1 | Connected to: Signal 100% |
|
| VINpin 2 | Connected to: BATT 83% · a signal 17% |
|
| ENpin 3 | Connected to: Signal 50% · not connected 17% · VCC 33% |
|
| RT/SYNCpin 4 | Connected to: Signal 100% |
|
| FBpin 5 | Connected to: Signal 100% |
|
| SSpin 6 | Connected to: Signal 100% |
|
| GNDpin 7, 9 | Connected to: GND 92% | — |
| SWpin 8 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Power Board by SSL-A-Team, TFSBEC01 by ThunderFly-aerospace, LION2CELL02 by mlab-modules and Seebum by peedrooh.
The LMR14050 in open source designs
The gallery holds 6 open source boards using the LMR14050 from 6 GitHub repositories; a typical one measures about 58.9 × 54.4 mm and carries around 65 components.
50% are two-layer designs, the rest use four layers or more, and 83% carry an open source license.
The most starred is Power Board by SSL-A-Team.
What boards using the LMR14050 are built for
LMR14050: common questions
Where can I find a LMR14050 reference design?
Each of the 6 boards on this page is a real design using the LMR14050. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LMR14050 BOOT pin connected?
The BOOT pin has a series capacitor on 6 of 6 designs, most often 100 nF. Counted from the KiCad layouts of 6 open source designs using the LMR14050.
What decoupling capacitors do designs use on the LMR14050 VIN pin?
The VIN pin has a decoupling capacitor on 6 of 6 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 6 open source designs using the LMR14050.
What resistor goes on the LMR14050 RT/SYNC pin?
The RT/SYNC pin has a resistor to GND on 6 of 6 designs, most often 133 kΩ (then 59 kΩ). Counted from the KiCad layouts of 6 open source designs using the LMR14050.
Which microcontrollers do boards using the LMR14050 use?
Most are built on ESP32 (1) and STM32 (1).
How big is a typical board using the LMR14050?
The median is 58.9 × 54.4 mm, and 50% are two-layer designs.
What is the most popular open source board using the LMR14050?
By GitHub stars, Power Board by SSL-A-Team, with 6 stars.
Can I simulate one of these boards using the LMR14050 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.