8 open source boards using the LMR51430YDDCR
Real designs built with the LMR51430YDDCR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Motherboard
JacobParent7
115 × 125 mm232 parts4LNo license11ESP32
WSPR-ease
alanmimms
99 × 64 mm171 parts4LMIT1STM32
Dsv4
suzizecat
188 × 110 mm250 parts4LNo license0STM32
Nereus Pi shield ADIN2111
nickraymond
62 × 37 mm161 parts6LNo license0ZeusController
GraffJosh
43 × 33 mm17 parts2LNo license0STM32
BM Mote 000639-AB
nickraymond
62 × 37 mm161 parts6LNo license0STM32
Power supply
suzizecat
100 × 100 mm126 parts4LNo license0STM32
Can repeater
sufst
69.5 × 27.7 mm53 parts4LGPL-3.019
How designs wire the LMR51430YDDCR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LMR51430YDDCR connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a inductor on 6 of 6 designs, most often 2.2 µH (then 3.3 µH).
- The SW pin has a series capacitor on 6 of 6 designs, most often 100 nF.
- The VIN pin has a decoupling capacitor on 5 of 6 designs, most often 1 µF (then 100 nF).
- The FB pin has a resistor to GND on 5 of 6 designs, most often 22.1 kΩ (then 13.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 100% | — |
| SWpin 2 | Connected to: Signal 83% · 3.3V 17% |
|
| VINpin 3 | Connected to: VBUS 50% · a signal 50% |
|
| FBpin 4 | Connected to: Signal 83% · 3.3V 17% |
|
| CBpin 6 | Connected to: Signal 100% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Can repeater by sufst, Motherboard by JacobParent7, WSPR-ease by alanmimms and ZeusController by GraffJosh.
The LMR51430YDDCR in open source designs
The gallery holds 8 open source boards using the LMR51430YDDCR from 6 GitHub repositories; a typical one measures about 84.2 × 50.5 mm and carries around 161 components.
88% use four copper layers or more, and 25% carry an open source license.
The most starred is Can repeater by sufst.
What boards using the LMR51430YDDCR are built for
LMR51430YDDCR: common questions
Where can I find a LMR51430YDDCR reference design?
Each of the 8 boards on this page is a real design using the LMR51430YDDCR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LMR51430YDDCR SW pin connected?
The SW pin has a inductor on 6 of 6 designs, most often 2.2 µH (then 3.3 µH). Counted from the KiCad layouts of 6 open source designs using the LMR51430YDDCR.
What decoupling capacitors do designs use on the LMR51430YDDCR VIN pin?
The VIN pin has a decoupling capacitor on 5 of 6 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 6 open source designs using the LMR51430YDDCR.
What resistor goes on the LMR51430YDDCR FB pin?
The FB pin has a resistor to GND on 5 of 6 designs, most often 22.1 kΩ (then 13.7 kΩ). Counted from the KiCad layouts of 6 open source designs using the LMR51430YDDCR.
Which microcontrollers do boards using the LMR51430YDDCR use?
Most are built on STM32 (6) and ESP32 (1).
How big is a typical board using the LMR51430YDDCR?
The median is 84.2 × 50.5 mm, and 13% are two-layer designs.
What is the most popular open source board using the LMR51430YDDCR?
By GitHub stars, Can repeater by sufst, with 19 stars.
Can I simulate one of these boards using the LMR51430YDDCR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.