6 open source boards using the LSM303C
Real designs built with the LSM303C, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
ENHP
sebmorales
76.3 × 105.1 mm44 parts2LNo license9BGeigieIntegrated
IRNAS
66.8 × 104.8 mm86 parts2LCustom license6ESP32
Esp32 tracker
cnlohr
7 × 7 mm91 parts2LMIT3AVR/Arduino
Avrcraft m644
cnlohr
85.1 × 49.8 mm49 parts2LNo license472Microchip SAM
Avionics Board 1
djmallek
50 × 50 mm63 parts2LNo license1STM32
BUT Pneumobil - HMI
kajusK
133.5 × 95 mm115 parts2LNo license0
How designs wire the LSM303C
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LSM303C connects to, and the resistors, capacitors and other passives placed on it.
- The SCL/SPC pin has a pull-up to 3.3V on 5 of 6 designs, most often 2.7 kΩ (then 10 kΩ).
- The SDA/SDI/SDO pin has a pull-up to 3.3V on 5 of 6 designs, most often 2.7 kΩ (then 10 kΩ).
- The C1 pin has a capacitor to GND on 5 of 6 designs, most often 100 nF (then 220 nF).
- The INT_MAG pin is left unconnected on 6 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SCL/SPCpin 1 | Connected to: The microcontroller 83%, a connector 67% |
|
| CS_XLpin 2 | Connected to: Signal 50% · not connected 17% · 3.3V 33% |
|
| CS_MAGpin 3 | Connected to: Signal 50% · not connected 17% · 3.3V 33% |
|
| SDA/SDI/SDOpin 4 | Connected to: The microcontroller 83%, a connector 67% |
|
| C1pin 5 | Connected to: Signal 100% |
|
| GNDpin 6, 8 | Connected to: GND 100% | — |
| INT_MAGpin 7 | Connected to: Not connected 100% | — |
| VDDpin 9 | Connected to: 3.3V 83% · a signal 17% |
|
| VDDIOpin 10 | Connected to: 3.3V 100% |
|
| DRDY_MAGpin 11 | Connected to: Not connected 100% | — |
| INT_XLpin 12 | Connected to: Not connected 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Avrcraft m644 by cnlohr, ENHP by sebmorales, BGeigieIntegrated by IRNAS and Esp32 tracker by cnlohr.
The LSM303C in open source designs
The gallery holds 6 open source boards using the LSM303C from 6 GitHub repositories; a typical one measures about 71.5 × 72.5 mm and carries around 75 components.
100% are two-layer designs, the rest use four layers or more, and 17% carry an open source license.
The most starred is Avrcraft m644 by cnlohr.
Parts used alongside the LSM303C
Microcontrollers on boards using the LSM303C
What boards using the LSM303C are built for
LSM303C: common questions
Where can I find a LSM303C reference design?
Each of the 6 boards on this page is a real design using the LSM303C. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the LSM303C SCL/SPC pin?
The SCL/SPC pin has a pull-up to 3.3V on 5 of 6 designs, most often 2.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 6 open source designs using the LSM303C.
What pull-up resistor is used on the LSM303C SDA/SDI/SDO pin?
The SDA/SDI/SDO pin has a pull-up to 3.3V on 5 of 6 designs, most often 2.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 6 open source designs using the LSM303C.
How is the LSM303C C1 pin connected?
The C1 pin has a capacitor to GND on 5 of 6 designs, most often 100 nF (then 220 nF). Counted from the KiCad layouts of 6 open source designs using the LSM303C.
Which microcontrollers do boards using the LSM303C use?
Most are built on ESP32 (2), AVR/Arduino (1), Microchip SAM (1) and STM32 (1).
How big is a typical board using the LSM303C?
The median is 71.5 × 72.5 mm, and 100% are two-layer designs.
What is the most popular open source board using the LSM303C?
By GitHub stars, Avrcraft m644 by cnlohr, with 472 stars.
Can I simulate one of these boards using the LSM303C before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.