6 open source boards using the LT3045EMSE#PBF

Real designs built with the LT3045EMSE#PBF, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the LT3045EMSE#PBF

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LT3045EMSE#PBF connects to, and the resistors, capacitors and other passives placed on it.

  • The PG pin is left unconnected on 6 of 6 designs.
  • The SET pin has a resistor to GND on 5 of 6 designs, most often 49.9 kΩ (then 69.8 kΩ).
  • The SET pin has a capacitor to GND on 5 of 6 designs, most often 100 nF (then 22 µF).
  • The OUT pins is tied to V+ on 100% of them.
INpin 1, 2, 3Connected to: 8V 67% · a signal 33%
EN/UVpin 4Connected to: 8V 67% · a signal 33%
PGpin 5Connected to: Not connected 100%
ILIMpin 6Connected to: GND 67% · a signal 33%
  • Resistor to GND on 33% · 499 Ω (1), 330 Ω (1)
PGFBpin 7Connected to: 8V 67% · a signal 33%
SETpin 8Connected to: Signal 100%
  • Resistor to GND on 83% · 49.9 kΩ (3), 69.8 kΩ (1), 33.2 kΩ (1)
  • Capacitor to GND on 83% · 100 nF (3), 22 µF (1), 4.7 µF (1)
GNDpin 9, 13Connected to: GND 100%
OUTSpin 10Connected to: V+ 83% · a signal 17%
OUTpin 11, 12Connected to: V+ 100%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Phase frequency detector by TU-Darmstadt-APQ, ELARA two bucket PSU by MatejGomboc, AD9954 TESTBOARD by elektrojupp and MTS module by TU-Darmstadt-APQ.

The LT3045EMSE#PBF in open source designs

The gallery holds 6 open source boards using the LT3045EMSE#PBF from 6 GitHub repositories; a typical one measures about 160 × 100 mm and carries around 103 components.

100% are two-layer designs, the rest use four layers or more, and 83% carry an open source license.

The most starred is Phase frequency detector by TU-Darmstadt-APQ.

Microcontrollers on boards using the LT3045EMSE#PBF

What boards using the LT3045EMSE#PBF are built for

LT3045EMSE#PBF: common questions

Where can I find a LT3045EMSE#PBF reference design?

Each of the 6 boards on this page is a real design using the LT3045EMSE#PBF. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the LT3045EMSE#PBF PG pin connected?

The PG pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the LT3045EMSE#PBF.

What resistor goes on the LT3045EMSE#PBF SET pin?

The SET pin has a resistor to GND on 5 of 6 designs, most often 49.9 kΩ (then 69.8 kΩ). Counted from the KiCad layouts of 6 open source designs using the LT3045EMSE#PBF.

How is the LT3045EMSE#PBF OUT pin connected?

The OUT pins is tied to V+ on 100% of them. Counted from the KiCad layouts of 6 open source designs using the LT3045EMSE#PBF.

What parts are used alongside the LT3045EMSE#PBF?

The LT3094EMSE#PBF, ADA4898-2YRDZ, L7808CV, L7812CV and L7908CV appear in the most repositories here.

Which microcontrollers do boards using the LT3045EMSE#PBF use?

Most are built on STM32 (1).

How big is a typical board using the LT3045EMSE#PBF?

The median is 160 × 100 mm, and 100% are two-layer designs.

What is the most popular open source board using the LT3045EMSE#PBF?

By GitHub stars, Phase frequency detector by TU-Darmstadt-APQ, with 7 stars.

Can I simulate one of these boards using the LT3045EMSE#PBF before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part