8 open source boards using the MAX809
Real designs built with the MAX809, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Audi concert1 chorus1 volume fix v3
tomaskovacik
34 × 26.2 mm46 parts2LGPL-3.017Microchip SAM
OpenBeacon3
etherkit
120 × 90 mm97 parts2LGPL-3.07Esp20A80V
RoboDurden
72.6 × 30.6 mm30 parts2LMIT2EVD80 MCU
Alexandr-Filatov
236 × 150 mm746 parts6LNo license0PIC
Vwcdpic with BT panel
tomaskovacik
82.8 × 72.1 mm70 parts2LGPL-2.029ESP32
ESP32C3 Slave PROFET
RoboDurden
80 × 33 mm29 parts2LMIT2ESP32
ESP32-bat monitor latch
pcbreflux
33 × 50 mm29 parts2LGPL-3.0608ESP32
ESP32-bat monitor latch pan
pcbreflux
66 × 100 mm29 parts2LGPL-3.0608
How designs wire the MAX809
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MAX809 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF.
- The RESET pin has a series resistor on 2 of 5 designs, most often 1 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 80% · a signal 20% | — |
| RESETpin 2 | Connected to: Signal 100% |
|
| VCCpin 3 | Connected to: 3.3V 80% · a signal 20% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Vwcdpic with BT panel by tomaskovacik, Audi concert1 chorus1 volume fix v3 by tomaskovacik, OpenBeacon3 by etherkit and Esp20A80V by RoboDurden.
The MAX809 in open source designs
The gallery holds 8 open source boards using the MAX809 from 6 GitHub repositories; a typical one measures about 76.3 × 61.1 mm and carries around 38 components.
88% are two-layer designs, the rest use four layers or more, and 88% carry an open source license.
The most starred is ESP32-bat monitor latch pan by pcbreflux.
Microcontrollers on boards using the MAX809
What boards using the MAX809 are built for
MAX809: common questions
Where can I find a MAX809 reference design?
Each of the 8 boards on this page is a real design using the MAX809. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MAX809 VCC pin?
The VCC pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the MAX809.
What resistor goes on the MAX809 RESET pin?
The RESET pin has a series resistor on 2 of 5 designs, most often 1 kΩ. Counted from the KiCad layouts of 5 open source designs using the MAX809.
Which microcontrollers do boards using the MAX809 use?
Most are built on ESP32 (3), PIC (1), Microchip SAM (1) and STM32 (1).
How big is a typical board using the MAX809?
The median is 76.3 × 61.1 mm, and 88% are two-layer designs.
What is the most popular open source board using the MAX809?
By GitHub stars, ESP32-bat monitor latch pan by pcbreflux, with 608 stars.
Can I simulate one of these boards using the MAX809 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.