5 open source boards using the MCP23S17_SP
Real designs built with the MCP23S17_SP, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
PocketTRS
apuder
87.6 × 83.6 mm48 parts2LNo license39AVR/Arduino
Sbc6502a1
tkhshmsy
95 × 100 mm36 parts2LMIT2RP2040/RP2350
Zx50 Bus Probe RevB
mmosko
145.9 × 147.3 mm80 parts4LNo license0AVR/Arduino
Pld test
gcoonrod
81.5 × 76.2 mm33 parts2LApache-2.00Spi port expander
niliha
35 × 43 mm12 parts2LGPL-3.01
How designs wire the MCP23S17_SP
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MCP23S17_SP connects to, and the resistors, capacitors and other passives placed on it.
- The A1 pin is tied to GND on 4 of 5 designs.
- The A2 pin is tied to GND on 4 of 5 designs.
- The INTB pin is left unconnected on 4 of 5 designs.
- The INTA pin is left unconnected on 4 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 9 | Connected to: 5V 100% |
|
| VSSpin 10 | Connected to: GND 100% | — |
| CSpin 11 | Connected to: The microcontroller 80% |
|
| A0pin 15 | Connected to: GND 60% · 5V 20% · a signal 20% | — |
| A1pin 16 | Connected to: GND 80% · a signal 20% | — |
| A2pin 17 | Connected to: GND 80% · a signal 20% | — |
| RESETpin 18 | Connected to: The microcontroller 80% · 3.3V 20% |
|
| INTBpin 19 | Connected to: Not connected 80% · a signal 20% | — |
| INTApin 20 | Connected to: Not connected 80% · a signal 20% | — |
19 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PocketTRS by apuder, Sbc6502a1 by tkhshmsy, Spi port expander by niliha and Pld test by gcoonrod.
The MCP23S17_SP in open source designs
The gallery holds 5 open source boards using the MCP23S17_SP from 5 GitHub repositories; a typical one measures about 87.6 × 83.6 mm and carries around 36 components.
80% are two-layer designs, the rest use four layers or more, and 60% carry an open source license.
The most starred is PocketTRS by apuder.
Microcontrollers on boards using the MCP23S17_SP
What boards using the MCP23S17_SP are built for
MCP23S17_SP: common questions
Where can I find a MCP23S17_SP reference design?
Each of the 5 boards on this page is a real design using the MCP23S17_SP. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MCP23S17_SP A1 pin connected?
The A1 pin is tied to GND on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the MCP23S17_SP.
How is the MCP23S17_SP A2 pin connected?
The A2 pin is tied to GND on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the MCP23S17_SP.
How is the MCP23S17_SP INTB pin connected?
The INTB pin is left unconnected on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the MCP23S17_SP.
Which microcontrollers do boards using the MCP23S17_SP use?
Most are built on AVR/Arduino (2), ESP32 (1) and RP2040/RP2350 (1).
How big is a typical board using the MCP23S17_SP?
The median is 87.6 × 83.6 mm, and 80% are two-layer designs.
What is the most popular open source board using the MCP23S17_SP?
By GitHub stars, PocketTRS by apuder, with 39 stars.
Can I simulate one of these boards using the MCP23S17_SP before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.