5 open source boards using the MCP4725A1T-E/CH
Real designs built with the MCP4725A1T-E/CH, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
OpenBeacon2
etherkit
100 × 80 mm74 parts2LNo license15RP2040/RP2350
YamhillFrontPanel
NT7S
170 × 100 mm207 parts4LNo license9Microchip SAM
OpenBeacon3
etherkit
120 × 90 mm97 parts2LGPL-3.07AVR/Arduino
Senior design
alaza252
50 × 60 mm24 parts2LNo license1RP2040/RP2350
Ultr4rick
kelu124
120 × 80 mm258 parts6LNo license0
How designs wire the MCP4725A1T-E/CH
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MCP4725A1T-E/CH connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 5V on 4 of 5 designs, most often 4.7 kΩ (then 3.3 kΩ).
- The SCL pin has a pull-up to 5V on 4 of 5 designs, most often 4.7 kΩ (then 3.3 kΩ).
- The A0 pin is tied to GND on 4 of 5 designs.
- The VOUT pin has a series resistor on 3 of 5 designs, most often 56 Ω (then 56 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VOUTpin 1 | Connected to: Signal 100% |
|
| VSSpin 2 | Connected to: GND 100% | — |
| VDDpin 3 | Connected to: 5V 80% · a signal 20% |
|
| SDApin 4 | Connected to: The microcontroller 80% |
|
| SCLpin 5 | Connected to: The microcontroller 80% |
|
| A0pin 6 | Connected to: GND 80% · not connected 20% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include OpenBeacon2 by etherkit, YamhillFrontPanel by NT7S, OpenBeacon3 by etherkit and Senior design by alaza252.
The MCP4725A1T-E/CH in open source designs
The gallery holds 5 open source boards using the MCP4725A1T-E/CH from 5 GitHub repositories; a typical one measures about 120 × 80 mm and carries around 97 components.
60% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.
The most starred is OpenBeacon2 by etherkit.
Parts used alongside the MCP4725A1T-E/CH
Microcontrollers on boards using the MCP4725A1T-E/CH
What boards using the MCP4725A1T-E/CH are built for
MCP4725A1T-E/CH: common questions
Where can I find a MCP4725A1T-E/CH reference design?
Each of the 5 boards on this page is a real design using the MCP4725A1T-E/CH. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the MCP4725A1T-E/CH SDA pin?
The SDA pin has a pull-up to 5V on 4 of 5 designs, most often 4.7 kΩ (then 3.3 kΩ). Counted from the KiCad layouts of 5 open source designs using the MCP4725A1T-E/CH.
What pull-up resistor is used on the MCP4725A1T-E/CH SCL pin?
The SCL pin has a pull-up to 5V on 4 of 5 designs, most often 4.7 kΩ (then 3.3 kΩ). Counted from the KiCad layouts of 5 open source designs using the MCP4725A1T-E/CH.
How is the MCP4725A1T-E/CH A0 pin connected?
The A0 pin is tied to GND on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the MCP4725A1T-E/CH.
Which microcontrollers do boards using the MCP4725A1T-E/CH use?
Most are built on RP2040/RP2350 (2), AVR/Arduino (1) and Microchip SAM (1).
How big is a typical board using the MCP4725A1T-E/CH?
The median is 120 × 80 mm, and 60% are two-layer designs.
What is the most popular open source board using the MCP4725A1T-E/CH?
By GitHub stars, OpenBeacon2 by etherkit, with 15 stars.
Can I simulate one of these boards using the MCP4725A1T-E/CH before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.