8 open source boards using the MCP9808
Real designs built with the MCP9808, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
DingoPDM
corygrant
72.4 × 95.3 mm151 parts4LMIT128STM32
Printalyzer UV/VIS Densitometer - Main Board
dektronics
105 × 38 mm81 parts4LNo license6ESP8266
NeOSensorV4 panel
fthiebolt
98.8 × 97.4 mm46 parts2LNo license5NXP
Infozilla
USSTRocketry
134 × 45 mm31 parts2LMIT1Lps regulator rev 12
jerryok826
136.2 × 62.6 mm122 parts2LMIT1TheHub
djmallek
118.8 × 184.2 mm42 parts2LNo license1Ring illuminator
plertvilai
73.5 × 73.5 mm23 parts2LMIT7Pcbv4-temp
fthiebolt
22.1 × 14.2 mm4 parts2LNo license5
How designs wire the MCP9808
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the MCP9808 connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 4 of 6 designs, most often 10 kΩ (then 2 kΩ).
- The SCL pin has a pull-up to 3.3V on 4 of 6 designs, most often 10 kΩ (then 2 kΩ).
- The VDD pin has a decoupling capacitor on 4 of 6 designs, most often 1 µF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SDApin 1 | Connected to: A connector 33% · 3.3V 17% |
|
| SCLpin 2 | Connected to: A connector 33% · GND 17% |
|
| GNDpin 4 | Connected to: GND 83% · a signal 17% | — |
| A2pin 5 | Connected to: GND 50% · not connected 17% · a signal 33% |
|
| A1pin 6 | Connected to: GND 50% · not connected 17% · a signal 33% |
|
| A0pin 7 | Connected to: GND 50% · not connected 17% · a signal 33% |
|
| VDDpin 8 | Connected to: 3.3V 83% · not connected 17% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include DingoPDM by corygrant, Ring illuminator by plertvilai, Printalyzer UV/VIS Densitometer - Main Board by dektronics and TheHub by djmallek.
The MCP9808 in open source designs
The gallery holds 8 open source boards using the MCP9808 from 7 GitHub repositories; a typical one measures about 101.9 × 68.1 mm and carries around 44 components.
75% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is DingoPDM by corygrant.
What boards using the MCP9808 are built for
MCP9808: common questions
Where can I find a MCP9808 reference design?
Each of the 8 boards on this page is a real design using the MCP9808. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the MCP9808 SDA pin?
The SDA pin has a pull-up to 3.3V on 4 of 6 designs, most often 10 kΩ (then 2 kΩ). Counted from the KiCad layouts of 6 open source designs using the MCP9808.
What pull-up resistor is used on the MCP9808 SCL pin?
The SCL pin has a pull-up to 3.3V on 4 of 6 designs, most often 10 kΩ (then 2 kΩ). Counted from the KiCad layouts of 6 open source designs using the MCP9808.
What decoupling capacitors do designs use on the MCP9808 VDD pin?
The VDD pin has a decoupling capacitor on 4 of 6 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 6 open source designs using the MCP9808.
Which microcontrollers do boards using the MCP9808 use?
Most are built on STM32 (2), ESP8266 (1) and NXP (1).
How big is a typical board using the MCP9808?
The median is 101.9 × 68.1 mm, and 75% are two-layer designs.
What is the most popular open source board using the MCP9808?
By GitHub stars, DingoPDM by corygrant, with 128 stars.
Can I simulate one of these boards using the MCP9808 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.