7 open source boards using the MT3608L
Real designs built with the MT3608L, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Raspberry Pi
Bmacro Base V2
KipJM
182.6 × 130.9 mm133 parts2LCERN-OHL-W-2.027RP2040/RP2350
Spacescape
Napkin-to-Billboard
205 × 140 mm327 parts4LMIT0STM32
Ultrasonic water depth measurement
ts01af
100 × 100 mm92 parts2LNo license0Quiz remote
nahhao74
52 × 90 mm66 parts2LMIT0EEE3088F 2025
TTembe
80 × 60 mm57 parts2LNo license0UCT-EEE3088F-Project
ShameeraC
100 × 100 mm46 parts2LNo license0Placed unrouted
nahhao74
52 × 90 mm66 parts2LMIT0
How designs wire the MT3608L
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the MT3608L connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a inductor on 5 of 6 designs, most often 4.7 µH (then 22 µH).
- The FB pin has a resistor to GND on 5 of 6 designs, most often 5.1 kΩ (then 15 kΩ).
- The EN pin has a capacitor to GND on 4 of 6 designs, most often 22 µF (then 100 nF).
- The VIN pin has a inductor on 4 of 6 designs, most often 4.7 µH (then 10 µH).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SWpin 1 | Connected to: Signal 100% |
|
| GNDpin 2 | Connected to: GND 83% · not connected 17% | — |
| FBpin 3 | Connected to: Signal 83% · GND 17% |
|
| ENpin 4 | Connected to: Signal 83% · VIN_BOOST 17% |
|
| VINpin 5 | Connected to: Signal 67% · VIN_BOOST 33% |
|
| OCpin 6 | Connected to: Not connected 50% · a signal 50% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Bmacro Base V2 by KipJM, Quiz remote by nahhao74, Spacescape by Napkin-to-Billboard and UCT-EEE3088F-Project by ShameeraC.
The MT3608L in open source designs
The gallery holds 7 open source boards using the MT3608L from 6 GitHub repositories; a typical one measures about 100 × 100 mm and carries around 66 components.
86% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.
The most starred is Bmacro Base V2 by KipJM.
Parts used alongside the MT3608L
Microcontrollers on boards using the MT3608L
What boards using the MT3608L are built for
MT3608L: common questions
Where can I find a MT3608L reference design?
Each of the 7 boards on this page is a real design using the MT3608L. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MT3608L SW pin connected?
The SW pin has a inductor on 5 of 6 designs, most often 4.7 µH (then 22 µH). Counted from the KiCad layouts of 6 open source designs using the MT3608L.
What resistor goes on the MT3608L FB pin?
The FB pin has a resistor to GND on 5 of 6 designs, most often 5.1 kΩ (then 15 kΩ). Counted from the KiCad layouts of 6 open source designs using the MT3608L.
How is the MT3608L EN pin connected?
The EN pin has a capacitor to GND on 4 of 6 designs, most often 22 µF (then 100 nF). Counted from the KiCad layouts of 6 open source designs using the MT3608L.
Which microcontrollers do boards using the MT3608L use?
Most are built on Raspberry Pi (1), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the MT3608L?
The median is 100 × 100 mm, and 86% are two-layer designs.
What is the most popular open source board using the MT3608L?
By GitHub stars, Bmacro Base V2 by KipJM, with 27 stars.
Can I simulate one of these boards using the MT3608L before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.