8 open source boards using the NC7WZ16P6X
Real designs built with the NC7WZ16P6X, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
DSP-ADAU1452
ohdsp
100 × 100 mm377 parts4LTAPR-OHL-1.068CoreOne xCORE200-Original
ohdsp
100 × 100 mm389 parts4LNo license19CoreOne xCORE200
ohdsp
100 × 100 mm351 parts4LTAPR-OHL-1.015Pi1MHzLevelShifter
kgl2001
26.9 × 50.8 mm34 parts2LCC-BY-SA-4.04RP2040/RP2350
75-Keyboard
Jyst7
85 × 56 mm67 parts4LMIT1RP2040/RP2350
MuKOB Main Board
MorseKOB
123.2 × 125.7 mm119 parts4LMIT0BMS Host Interface Splitter
TERA-TU-Graz
57.5 × 49.5 mm154 parts4LSHL-2.13RP2040/RP2350
RPI-PVSA VGA, SD Card & Audio Demo Board for Pico
GearBoxFox
85 × 56 mm67 parts4LNo license2
How designs wire the NC7WZ16P6X
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the NC7WZ16P6X connects to, and the resistors, capacitors and other passives placed on it.
- The Y2 pin has a series resistor on 8 of 8 designs, most often 220 Ω (then 33 Ω).
- The VCC pin has a decoupling capacitor on 8 of 8 designs, most often 100 nF (then 10 µF).
- The Y1 pin has a series resistor on 7 of 8 designs, most often 220 Ω (then 33 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A1pin 1 | Connected to: A connector 25%, the microcontroller 25% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| A2pin 3 | Connected to: A connector 38%, the microcontroller 25% |
|
| Y2pin 4 | Connected to: Signal 100% |
|
| VCCpin 5 | Connected to: 3.3V 88% |
|
| Y1pin 6 | Connected to: Signal 88% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include DSP-ADAU1452 by ohdsp, CoreOne xCORE200-Original by ohdsp, CoreOne xCORE200 by ohdsp and Pi1MHzLevelShifter by kgl2001.
The NC7WZ16P6X in open source designs
The gallery holds 8 open source boards using the NC7WZ16P6X from 8 GitHub repositories; a typical one measures about 92.5 × 78 mm and carries around 137 components.
88% use four copper layers or more, and 63% carry an open source license.
The most starred is DSP-ADAU1452 by ohdsp.
Parts used alongside the NC7WZ16P6X
Microcontrollers on boards using the NC7WZ16P6X
What boards using the NC7WZ16P6X are built for
NC7WZ16P6X: common questions
Where can I find a NC7WZ16P6X reference design?
Each of the 8 boards on this page is a real design using the NC7WZ16P6X. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the NC7WZ16P6X Y2 pin?
The Y2 pin has a series resistor on 8 of 8 designs, most often 220 Ω (then 33 Ω). Counted from the KiCad layouts of 8 open source designs using the NC7WZ16P6X.
What decoupling capacitors do designs use on the NC7WZ16P6X VCC pin?
The VCC pin has a decoupling capacitor on 8 of 8 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 8 open source designs using the NC7WZ16P6X.
What resistor goes on the NC7WZ16P6X Y1 pin?
The Y1 pin has a series resistor on 7 of 8 designs, most often 220 Ω (then 33 Ω). Counted from the KiCad layouts of 8 open source designs using the NC7WZ16P6X.
What parts are used alongside the NC7WZ16P6X?
The 74HC04, IC-SPDIF-RX-OPTO, IC-SPDIF-TX-OPTO, CS2200-CP and IC-FLASH-SPI appear in the most repositories here.
Which microcontrollers do boards using the NC7WZ16P6X use?
Most are built on RP2040/RP2350 (3).
How big is a typical board using the NC7WZ16P6X?
The median is 92.5 × 78 mm, and 13% are two-layer designs.
What is the most popular open source board using the NC7WZ16P6X?
By GitHub stars, DSP-ADAU1452 by ohdsp, with 68 stars.
Can I simulate one of these boards using the NC7WZ16P6X before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.