8 open source boards using the OKI-78SR-3.3_1.5-W36-C
Real designs built with the OKI-78SR-3.3_1.5-W36-C, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Slave Board
columbia-fsae
412.7 × 77.5 mm148 parts2LNo license1STM32
IFS09-ES-SmartFuses
isc-fs
170 × 85 mm147 parts2LNo license0Main unit
HyFiVeUser
55 × 72.1 mm128 parts4LCC-BY-SA-4.00ESP32
Ece445-autonomous wifi mapping car
BenMaydan
100 × 100 mm82 parts2LNo license0AVR/Arduino
Smart-Ventilator
yesitha
156.3 × 179.5 mm69 parts2LNo license0ESP32
Screwdriver antenna auto tuner
k8tar
100 × 70 mm47 parts4LMIT0XNAV650-Ouster-Adapter-Enclosure
SoloScriptSage
27.7 × 35.6 mm15 parts2LNo license0AVR/Arduino
Meniscus controller
EdSmithe
76 × 91 mm10 parts2LNo license0
How designs wire the OKI-78SR-3.3_1.5-W36-C
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the OKI-78SR-3.3_1.5-W36-C connects to, and the resistors, capacitors and other passives placed on it.
- The OUT pin is tied to 3.3V on 7 of 8 designs.
- The IN pin is tied to 12V on 5 of 8 designs (a signal on 3).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| INpin 1 | Connected to: 12V 63% · a signal 38% | — |
| GNDpin 2 | Connected to: GND 88% | — |
| OUTpin 3 | Connected to: 3.3V 88% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Slave Board by columbia-fsae, Ece445-autonomous wifi mapping car by BenMaydan, Meniscus controller by EdSmithe and Main unit by HyFiVeUser.
The OKI-78SR-3.3_1.5-W36-C in open source designs
The gallery holds 8 open source boards using the OKI-78SR-3.3_1.5-W36-C from 8 GitHub repositories; a typical one measures about 100 × 81.2 mm and carries around 76 components.
75% are two-layer designs, the rest use four layers or more, and 25% carry an open source license.
The most starred is Slave Board by columbia-fsae.
Microcontrollers on boards using the OKI-78SR-3.3_1.5-W36-C
What boards using the OKI-78SR-3.3_1.5-W36-C are built for
OKI-78SR-3.3_1.5-W36-C: common questions
Where can I find a OKI-78SR-3.3_1.5-W36-C reference design?
Each of the 8 boards on this page is a real design using the OKI-78SR-3.3_1.5-W36-C. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the OKI-78SR-3.3_1.5-W36-C OUT pin connected?
The OUT pin is tied to 3.3V on 7 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the OKI-78SR-3.3_1.5-W36-C.
How is the OKI-78SR-3.3_1.5-W36-C IN pin connected?
The IN pin is tied to 12V on 5 of 8 designs (a signal on 3). Counted from the KiCad layouts of 8 open source designs using the OKI-78SR-3.3_1.5-W36-C.
Which microcontrollers do boards using the OKI-78SR-3.3_1.5-W36-C use?
Most are built on AVR/Arduino (3), ESP32 (2) and STM32 (1).
How big is a typical board using the OKI-78SR-3.3_1.5-W36-C?
The median is 100 × 81.2 mm, and 75% are two-layer designs.
What is the most popular open source board using the OKI-78SR-3.3_1.5-W36-C?
By GitHub stars, Slave Board by columbia-fsae, with 1 stars.
Can I simulate one of these boards using the OKI-78SR-3.3_1.5-W36-C before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.