7 open source boards using the OPA1611

Real designs built with the OPA1611, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the OPA1611

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the OPA1611 connects to, and the resistors, capacitors and other passives placed on it.

  • The - pin has a series resistor on 3 of 5 designs, most often 3.48 kΩ (then 3.6 kΩ).
  • The + pin has a capacitor to GND on 3 of 5 designs, most often 10 µF (then 470 pF).
  • Pin 6 has a series resistor on 3 of 5 designs, most often 3.6 kΩ (then 4.7 kΩ).
  • The V+ pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF (then 1 µF).
NCpin 1, 5, 8Connected to: Not connected 80% · a signal 20%
-pin 2Connected to: Signal 80% · 5V 20%
  • Series resistor on 60% · 3.48 kΩ (1), 3.6 kΩ (1), 150 Ω (1)
  • Series capacitor on 40% · 470 pF (1), 220 pF (1)
+pin 3Connected to: Signal 60% · GND 20% · 12V 20%
  • Capacitor to GND on 60% · 10 µF (2), 470 pF (1)
  • Pull-up to VCC on 40% · 680 Ω (1), 1 kΩ (1)
V-pin 4Connected to: GND 40% · -10V 20% · a signal 40%
  • Series resistor on 40% · 620 Ω (1), 5.6 kΩ (1)
  • Capacitor to GND on 40% · 100 nF (5), 1 µF (1)
Pin 6Connected to: Signal 80% · GND 20%
  • Series resistor on 60% · 3.6 kΩ (1), 4.7 kΩ (1), 10 Ω (1)
  • Series capacitor on 40% · 22 nF (2), 470 pF (1), 10 µF (1)
V+pin 7Connected to: VCC_HI 80% · not connected 20%
  • Decoupling capacitor on 60% · 100 nF (2), 1 µF (2), 47 µF (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include BalancedDriverBoard by freeDSP, Current dr amp by werediver, Electronics uldosc by mpinese and Mes main board by jmh8231-Dev.

The OPA1611 in open source designs

The gallery holds 7 open source boards using the OPA1611 from 5 GitHub repositories; a typical one measures about 100 × 90 mm and carries around 126 components.

71% are two-layer designs, the rest use four layers or more, and 43% carry an open source license.

The most starred is FreeDSP Catamaran by freeDSP.

Microcontrollers on boards using the OPA1611

What boards using the OPA1611 are built for

OPA1611: common questions

Where can I find a OPA1611 reference design?

Each of the 7 boards on this page is a real design using the OPA1611. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the OPA1611 - pin?

The - pin has a series resistor on 3 of 5 designs, most often 3.48 kΩ (then 3.6 kΩ). Counted from the KiCad layouts of 5 open source designs using the OPA1611.

How is the OPA1611 + pin connected?

The + pin has a capacitor to GND on 3 of 5 designs, most often 10 µF (then 470 pF). Counted from the KiCad layouts of 5 open source designs using the OPA1611.

What resistor goes on the OPA1611 pin 6?

Pin 6 has a series resistor on 3 of 5 designs, most often 3.6 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 5 open source designs using the OPA1611.

Which microcontrollers do boards using the OPA1611 use?

Most are built on STM32 (1).

How big is a typical board using the OPA1611?

The median is 100 × 90 mm, and 71% are two-layer designs.

What is the most popular open source board using the OPA1611?

By GitHub stars, FreeDSP Catamaran by freeDSP, with 11 stars.

Can I simulate one of these boards using the OPA1611 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part