6 open source boards using the OPA1612
Real designs built with the OPA1612, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
EmoeNAP
Floyd-Fish
75 × 36 mm156 parts4LGPL-3.035Iridium-ADC
ABillBlakely
82.5 × 70 mm111 parts2LGPL-3.02STM32
Relock Artiq
KLFAMO
161 × 100 mm375 parts4LNo license0STM32
HiFiDAC
BlockWorker
40 × 40 mm102 parts4LNo license2Tonemender2
jonronen
91.8 × 54.1 mm38 parts2LNo license1Tonemender
jonronen
90.8 × 38.1 mm27 parts2LNo license1
How designs wire the OPA1612
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the OPA1612 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 4 of 5 designs, most often 249 Ω (then 1 Ω).
- The - pins have a series resistor on 4 of 5 designs, most often 349 Ω (then 249 Ω).
- The + pins have a series resistor on 4 of 5 designs, most often 10 Ω (then 1 MΩ).
- The V+ pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 2.2 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| -pin 2, 6 | Connected to: Signal 100% |
|
| +pin 3, 5 | Connected to: OPA1612 20% |
|
| V-pin 4 | Connected to: GND 60% · -15V 40% | — |
| Pin 7 | Connected to: Signal 100% |
|
| V+pin 8 | Connected to: 12V 100% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EmoeNAP by Floyd-Fish, Iridium-ADC by ABillBlakely, HiFiDAC by BlockWorker and Tonemender by jonronen.
The OPA1612 in open source designs
The gallery holds 6 open source boards using the OPA1612 from 5 GitHub repositories; a typical one measures about 86.7 × 47 mm and carries around 107 components.
50% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is EmoeNAP by Floyd-Fish.
Microcontrollers on boards using the OPA1612
What boards using the OPA1612 are built for
OPA1612: common questions
Where can I find a OPA1612 reference design?
Each of the 6 boards on this page is a real design using the OPA1612. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the OPA1612 pin 1?
Pin 1 has a series resistor on 4 of 5 designs, most often 249 Ω (then 1 Ω). Counted from the KiCad layouts of 5 open source designs using the OPA1612.
What resistor goes on the OPA1612 - pin?
The - pins have a series resistor on 4 of 5 designs, most often 349 Ω (then 249 Ω). Counted from the KiCad layouts of 5 open source designs using the OPA1612.
What resistor goes on the OPA1612 + pin?
The + pins have a series resistor on 4 of 5 designs, most often 10 Ω (then 1 MΩ). Counted from the KiCad layouts of 5 open source designs using the OPA1612.
Which microcontrollers do boards using the OPA1612 use?
Most are built on STM32 (2).
How big is a typical board using the OPA1612?
The median is 86.7 × 47 mm, and 50% are two-layer designs.
What is the most popular open source board using the OPA1612?
By GitHub stars, EmoeNAP by Floyd-Fish, with 35 stars.
Can I simulate one of these boards using the OPA1612 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.