6 open source boards using the OPA4171
Real designs built with the OPA4171, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Cats eye
lennartquerter
90 × 110 mm223 parts4LCC-BY-NC-4.012STM32
Marbles v70
mort13
88.9 × 106.1 mm207 parts2LGPL-3.012STM32
Bmcv
Bemeier
80 × 108 mm370 parts4LCC-BY-SA-4.07Jinx
kstammits
20 × 128.5 mm98 parts2LNo license5K2
kstammits
20 × 128.5 mm81 parts2LNo license5Buffer 1.2
rhinocerose
19.1 × 108.5 mm50 parts2LNo license0
How designs wire the OPA4171
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the OPA4171 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 5 of 5 designs, most often 1 kΩ (then 100 Ω).
- The - pins have a series resistor on 5 of 5 designs, most often 100 kΩ (then 23.7 kΩ).
- The V+ pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 10 µF).
- The V- pin has a capacitor to GND on 5 of 5 designs, most often 100 nF (then 22 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| -pin 2, 6, 9, 13 | Connected to: Signal 100% |
|
| +pin 3, 5, 10, 12 | Connected to: A connector 25% · 1V 40% |
|
| V+pin 4 | Connected to: VCC 100% |
|
| Pin 7 | Connected to: TL074 40% |
|
| Pin 8 | Connected to: Signal 100% |
|
| V-pin 11 | Connected to: Signal 60% · -12V 40% |
|
| Pin 14 | Connected to: TL074 40% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Cats eye by lennartquerter, Marbles v70 by mort13, Bmcv by Bemeier and Jinx by kstammits.
The OPA4171 in open source designs
The gallery holds 6 open source boards using the OPA4171 from 5 GitHub repositories; a typical one measures about 50 × 109.3 mm and carries around 153 components.
67% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is Cats eye by lennartquerter.
Microcontrollers on boards using the OPA4171
What boards using the OPA4171 are built for
OPA4171: common questions
Where can I find a OPA4171 reference design?
Each of the 6 boards on this page is a real design using the OPA4171. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the OPA4171 pin 1?
Pin 1 has a series resistor on 5 of 5 designs, most often 1 kΩ (then 100 Ω). Counted from the KiCad layouts of 5 open source designs using the OPA4171.
What resistor goes on the OPA4171 - pin?
The - pins have a series resistor on 5 of 5 designs, most often 100 kΩ (then 23.7 kΩ). Counted from the KiCad layouts of 5 open source designs using the OPA4171.
What decoupling capacitors do designs use on the OPA4171 V+ pin?
The V+ pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the OPA4171.
What parts are used alongside the OPA4171?
The MCP6004, TL072 and TL074 appear in the most repositories here.
Which microcontrollers do boards using the OPA4171 use?
Most are built on STM32 (3).
How big is a typical board using the OPA4171?
The median is 50 × 109.3 mm, and 67% are two-layer designs.
What is the most popular open source board using the OPA4171?
By GitHub stars, Cats eye by lennartquerter, with 12 stars.
Can I simulate one of these boards using the OPA4171 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.