5 open source boards using the PAM2401SCADJ
Real designs built with the PAM2401SCADJ, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Pi tin main
jackw01
89 × 55.5 mm77 parts2LCERN-OHL-W-2.073Tph Synth Featherwing
whatnick
51 × 58.5 mm47 parts2LNo license1Renesas
Project SolarPoints
Grolla05
40 × 85 mm102 partsNo license0AVR/Arduino
Night light
camerongillingham93
85 × 85 mm40 parts2LNo license0PIC
VolvocineWithCurrentSensorV4
KuraLab
29 × 32.3 mm29 parts2LNo license0
How designs wire the PAM2401SCADJ
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the PAM2401SCADJ connects to, and the resistors, capacitors and other passives placed on it.
- The LX pin has a inductor on 5 of 5 designs, most often 2.2 µH.
- The VIN pin has a decoupling capacitor on 5 of 5 designs, most often 22 µF (then 100 nF).
- The FB pin has a resistor to GND on 5 of 5 designs, most often 100 kΩ (then 47 kΩ).
- The EN pin has a pull-up to BATT on 4 of 5 designs, most often 100 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| LXpin 1 | Connected to: Signal 100% |
|
| ENpin 2 | Connected to: Signal 100% |
|
| VINpin 3 | Connected to: BATT 80% · a signal 20% |
|
| AGNDpin 4 | Connected to: GND 100% | — |
| FBpin 5 | Connected to: Signal 100% |
|
| RSETpin 6 | Connected to: Not connected 80% · a signal 20% | — |
| OUTpin 7 | Connected to: 5V 80% · a signal 20% | — |
| PGNDpin 8 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Pi tin main by jackw01, Tph Synth Featherwing by whatnick, Night light by camerongillingham93 and Project SolarPoints by Grolla05.
The PAM2401SCADJ in open source designs
The gallery holds 5 open source boards using the PAM2401SCADJ from 5 GitHub repositories; a typical one measures about 51 × 58.5 mm and carries around 47 components.
100% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.
The most starred is Pi tin main by jackw01.
Microcontrollers on boards using the PAM2401SCADJ
What boards using the PAM2401SCADJ are built for
PAM2401SCADJ: common questions
Where can I find a PAM2401SCADJ reference design?
Each of the 5 boards on this page is a real design using the PAM2401SCADJ. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the PAM2401SCADJ LX pin connected?
The LX pin has a inductor on 5 of 5 designs, most often 2.2 µH. Counted from the KiCad layouts of 5 open source designs using the PAM2401SCADJ.
What decoupling capacitors do designs use on the PAM2401SCADJ VIN pin?
The VIN pin has a decoupling capacitor on 5 of 5 designs, most often 22 µF (then 100 nF). Counted from the KiCad layouts of 5 open source designs using the PAM2401SCADJ.
What resistor goes on the PAM2401SCADJ FB pin?
The FB pin has a resistor to GND on 5 of 5 designs, most often 100 kΩ (then 47 kΩ). Counted from the KiCad layouts of 5 open source designs using the PAM2401SCADJ.
Which microcontrollers do boards using the PAM2401SCADJ use?
Most are built on AVR/Arduino (1), PIC (1) and Renesas (1).
How big is a typical board using the PAM2401SCADJ?
The median is 51 × 58.5 mm, and 100% are two-layer designs.
What is the most popular open source board using the PAM2401SCADJ?
By GitHub stars, Pi tin main by jackw01, with 73 stars.
Can I simulate one of these boards using the PAM2401SCADJ before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.