5 open source boards using the PCF8523T/1,118
Real designs built with the PCF8523T/1,118, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
CheetoPet
Cheet0sDelet0s
50.2 × 95.2 mm96 parts2LGPL-2.03AVR/Arduino
CIWS-MWM-Logger
UCHIC
110 × 60 mm40 parts2LBSD-3-Clause2RP2040/RP2350
Rp2040-timer
smaroukis
100 × 100 mm154 parts4LMIT0Nordic nRF
RoomSensor
mbush91
40.6 × 22.3 mm26 parts2LNo license0STM32
TideBand — Wrist-Worn Hydrographic Current Profiler
jayis1
62 × 52 mm24 parts5LNo license0
How designs wire the PCF8523T/1,118
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the PCF8523T/1,118 connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ).
- The SCL pin has a pull-up to 3.3V on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ).
- The OSCI pin has a crystal on 3 of 4 designs, most often 32.768 kHz.
- The OSCO pin has a crystal on 3 of 4 designs, most often 32.768 kHz.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OSCIpin 1 | Connected to: Signal 100% |
|
| OSCOpin 2 | Connected to: Signal 100% |
|
| VBATpin 3 | Connected to: BAT+ 60% · GND 20% · a signal 20% | — |
| VSSpin 4 | Connected to: GND 80% · 3.3V 20% | — |
| SDApin 5 | Connected to: The microcontroller 80% |
|
| SCLpin 6 | Connected to: The microcontroller 80% |
|
| INT1/CLKOUTpin 7 | Connected to: The microcontroller 75% |
|
| VDDpin 8 | Connected to: 3.3V 80% · a signal 20% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include CheetoPet by Cheet0sDelet0s, CIWS-MWM-Logger by UCHIC, TideBand — Wrist-Worn Hydrographic Current Profiler by jayis1 and RoomSensor by mbush91.
The PCF8523T/1,118 in open source designs
The gallery holds 5 open source boards using the PCF8523T/1,118 from 5 GitHub repositories; a typical one measures about 62 × 60 mm and carries around 40 components.
60% are two-layer designs, the rest use four layers or more, and 60% carry an open source license.
The most starred is CheetoPet by Cheet0sDelet0s.
Microcontrollers on boards using the PCF8523T/1,118
What boards using the PCF8523T/1,118 are built for
PCF8523T/1,118: common questions
Where can I find a PCF8523T/1,118 reference design?
Each of the 5 boards on this page is a real design using the PCF8523T/1,118. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the PCF8523T/1,118 SDA pin?
The SDA pin has a pull-up to 3.3V on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the PCF8523T/1,118.
What pull-up resistor is used on the PCF8523T/1,118 SCL pin?
The SCL pin has a pull-up to 3.3V on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the PCF8523T/1,118.
How is the PCF8523T/1,118 OSCI pin connected?
The OSCI pin has a crystal on 3 of 4 designs, most often 32.768 kHz. Counted from the KiCad layouts of 5 open source designs using the PCF8523T/1,118.
Which microcontrollers do boards using the PCF8523T/1,118 use?
Most are built on AVR/Arduino (1), ESP32 (1), Nordic nRF (1) and RP2040/RP2350 (1).
How big is a typical board using the PCF8523T/1,118?
The median is 62 × 60 mm, and 60% are two-layer designs.
What is the most popular open source board using the PCF8523T/1,118?
By GitHub stars, CheetoPet by Cheet0sDelet0s, with 3 stars.
Can I simulate one of these boards using the PCF8523T/1,118 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.