7 open source boards using the PJ-320A
Real designs built with the PJ-320A, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Key ripper
bschwind
285.8 × 116.7 mm211 parts2LApache-2.0288Gatebench
alheir
150 × 150 mm305 parts4LCERN-OHL-P-2.00ESP8266
EcoLogic
spspider
48 × 82 mm82 parts2LNo license0BTM308-host
KingJacker
23 × 40 mm52 parts4LNo license0RP2040/RP2350
Custom Hackboard
FabioCastroMorffi
124.6 × 130.5 mm39 parts2LNo license0Io patchbox
wistoff
60 × 51 mm18 parts2LNo license0BTM308-host bottom
KingJacker
23 × 40 mm36 parts4LNo license0
How designs wire the PJ-320A
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the PJ-320A connects to, and the resistors, capacitors and other passives placed on it.
- The TIP pin has a series resistor on 3 of 6 designs, most often 1 kΩ (then 47 Ω).
- The SLEEVE pin is tied to GND on 3 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SLEEVEpin 1 | Connected to: GND 60% · not connected 20% · a signal 20% | — |
| TIPpin 2 | Connected to: Signal 50% · not connected 17% · GND 17% · 5V 17% |
|
| RING1pin 3 | Connected to: Signal 67% · not connected 17% · 5V 17% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Key ripper by bschwind, Gatebench by alheir, Custom Hackboard by FabioCastroMorffi and BTM308-host by KingJacker.
The PJ-320A in open source designs
The gallery holds 7 open source boards using the PJ-320A from 6 GitHub repositories; a typical one measures about 60 × 82 mm and carries around 52 components.
57% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.
The most starred is Key ripper by bschwind.
Microcontrollers on boards using the PJ-320A
What boards using the PJ-320A are built for
PJ-320A: common questions
Where can I find a PJ-320A reference design?
Each of the 7 boards on this page is a real design using the PJ-320A. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the PJ-320A TIP pin?
The TIP pin has a series resistor on 3 of 6 designs, most often 1 kΩ (then 47 Ω). Counted from the KiCad layouts of 6 open source designs using the PJ-320A.
How is the PJ-320A SLEEVE pin connected?
The SLEEVE pin is tied to GND on 3 of 5 designs. Counted from the KiCad layouts of 6 open source designs using the PJ-320A.
Which microcontrollers do boards using the PJ-320A use?
Most are built on RP2040/RP2350 (2) and ESP8266 (1).
How big is a typical board using the PJ-320A?
The median is 60 × 82 mm, and 57% are two-layer designs.
What is the most popular open source board using the PJ-320A?
By GitHub stars, Key ripper by bschwind, with 288 stars.
Can I simulate one of these boards using the PJ-320A before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.