9 open source boards using the SHT30-DIS

Real designs built with the SHT30-DIS, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

9 boardsClear filters|Most starred

How designs wire the SHT30-DIS

Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the SHT30-DIS connects to, and the resistors, capacitors and other passives placed on it.

  • The SDA pin has a pull-up to 3.3V on 7 of 8 designs, most often 4.7 kΩ (then 10 kΩ).
  • The SCL pin has a pull-up to 3.3V on 7 of 8 designs, most often 4.7 kΩ (then 10 kΩ).
  • The VDD pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 4.7 µF).
  • The ADDR pin is tied to GND on 8 of 8 designs.
SDApin 1Connected to: The microcontroller 75%, a connector 25%
  • Pull-up to 3.3V on 88% · 4.7 kΩ (4), 10 kΩ (1), 5.1 kΩ (1)
ADDRpin 2Connected to: GND 100%
ALERTpin 3Connected to: Not connected 88%
SCLpin 4Connected to: The microcontroller 75%, a connector 25%
  • Pull-up to 3.3V on 88% · 4.7 kΩ (4), 10 kΩ (1), 5.1 kΩ (1)
VDDpin 5Connected to: 3.3V 100%
  • Decoupling capacitor on 88% · 100 nF (12), 4.7 µF (1)
RESETpin 6Connected to: Not connected 63% · VCC 25%
Rpin 7Connected to: GND 100%
VSSpin 8, 9Connected to: GND 100%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Terrarium Control Board by justbuchanan, AWS IoT ExpressLink Demo Badge by aws, Haptic knob by wirano and Sensor stick by AirMQ.

The SHT30-DIS in open source designs

The gallery holds 9 open source boards using the SHT30-DIS from 9 GitHub repositories; a typical one measures about 52 × 50 mm and carries around 58 components.

67% are two-layer designs, the rest use four layers or more, and 67% carry an open source license.

The most starred is Terrarium Control Board by justbuchanan.

Parts used alongside the SHT30-DIS

Microcontrollers on boards using the SHT30-DIS

SHT30-DIS: common questions

Where can I find a SHT30-DIS reference design?

Each of the 9 boards on this page is a real design using the SHT30-DIS. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the SHT30-DIS SDA pin?

The SDA pin has a pull-up to 3.3V on 7 of 8 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 8 open source designs using the SHT30-DIS.

What pull-up resistor is used on the SHT30-DIS SCL pin?

The SCL pin has a pull-up to 3.3V on 7 of 8 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 8 open source designs using the SHT30-DIS.

What decoupling capacitors do designs use on the SHT30-DIS VDD pin?

The VDD pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 8 open source designs using the SHT30-DIS.

Which microcontrollers do boards using the SHT30-DIS use?

Most are built on ESP32 (4), RP2040/RP2350 (2), GD32 (1) and STM32 (1).

How big is a typical board using the SHT30-DIS?

The median is 52 × 50 mm, and 67% are two-layer designs.

What is the most popular open source board using the SHT30-DIS?

By GitHub stars, Terrarium Control Board by justbuchanan, with 270 stars.

Can I simulate one of these boards using the SHT30-DIS before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part